Jump to content
SAU Community

Recommended Posts

Hey everyone

i'v got about 10k to spend on a car, i was wondering if that is enough to get me into a decent turbo manual skyline ?

It doesn't need to have any mods, i'm just looking for a car with decent k's and in good condition.

What do you think i would be looking at ? R32gts-t ? R33gst25t?

all replies are appreciated !

Link to comment
https://www.sau.com.au/forums/topic/188740-10k-enough/
Share on other sites

Yeah around the $10-$12,000 mark for a 32. As with all imports dont get hopes up about km readings, judge the amount of wear and tear on both the interior and engine bay to the odometer display. Also trying to find a 32 with no mods is quite low as most skylines have some sort of mods done to them. Best bet is to try car sale sites.

Link to comment
https://www.sau.com.au/forums/topic/188740-10k-enough/#findComment-3402641
Share on other sites

Do a search at www.carsales.com.au and uniquecarsales there are a few which may interest you and it will also gie a good idea of what you will get for the $$$. As said above will not be many in stock form. I rekon get one with only basic mods, like exhaust, fmic. I just had a quick look and there's a couple of R33 GTST's for 10k.

I have bought a few cars through carsales and never had a problem. Just make sure to do the research first and have the car fully inspected before paying anything.

Good luck.

Link to comment
https://www.sau.com.au/forums/topic/188740-10k-enough/#findComment-3403034
Share on other sites

Personally i reckon with a little patience you can just go for an R33. I waited SIX months from when i wanted one til when i bought it.

In that time i researched EVERYTHING about them, saved 10 G's cash, got price estimates for the car + insurance + transfering rego etc etc. I also attempted importing.

I ended up with a neat R33 for a few grand more than what u wanna spend and it's NEWER than an R32, more POWERFUL than an R32 and arguably BETTER LOOKING too. Also it's mechanically newer and that's important repair-cost wise.

My 2c is wait a little longer and get a better car (though not to bag the excellent R32) that you can keep for a while longer and really enjoy.

Good luck

Link to comment
https://www.sau.com.au/forums/topic/188740-10k-enough/#findComment-3405076
Share on other sites

Yeah I would go for an R33 if I could but, since I am only 22, I think I need to keep aside at least 2k for insurance and all that stuff.

And also I can't really be bothered buying a new car only to convert it from auto to manual or from NA to turbo or whatever, but thanks for the reply anyway.

All replies are appreciated !

Link to comment
https://www.sau.com.au/forums/topic/188740-10k-enough/#findComment-3406820
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...