Jump to content
SAU Community

Recommended Posts

The Plan:

I needed somewhere to mount my new amp. I already have and amp in the car that drives my sub, but needed a neat way to mount the new amp to drive my 4 speakers. I was going to just mount it under the seat or something like that, but Ant (Arch6) convinced me to go all out and make a false boot floor. I wanted to keep the car as original looking as possible while having a functional install.

Current Setup:

Panasonic CQ-C9901 Headdeck driving 4x infiniti components

350W Alpine Amp Driving 8" Kicker Solo-Baric Square Sub

New Setup

Panasonic CQ-C9901

Rockford Fosgate P4004 driving 4x infiniti components

350W Alpine Amp Driving 8" Kicker Solo-Baric Square Sub

1 Farad Cap

I've includes plenty of photo's in-case anyone else is keen on doing this.

I still need to sand and paint the panels, so it's not quite done yet.

First, We put the car onto ramps to make the boot a nice working height that won't break out backs

easywork.JPG

This is my current setup. Amp on the left and sub on the right

boot1.JPG

Removing the bracing reveals...

batampsub.JPG

Amp is mounted onto the side of the battery bay.

batteryamp.JPG

Amp Mount. The wires run under the amp and so all wires are nicely hidden. Probably goint to paint it black)

rf1.JPG

Next step was to make the mount for the Cap. Because there was no room and it was taller then the amp i had no choice but to mount it on top of the spare tyre.

tyrecap.JPG

The metal/wood plate that the Cap sits on it held in place by three very very strong magnets.

magnets.JPG

this way, if I do get a flat I just have to move the cap off the amp side and remove the spare tyre.

I could probably store some tools and my first aid kit on this side :D

floor3.JPG

Putting it all together

tyrecap2.JPG

floor1.JPG

floor2.JPG

Bacause i'd raised the floor the factory carpet would no longer fit. So i had to get new carpet for the floor.

Cutting out the carpet.

carpetcut.JPG

carpet1.JPG

Got the edge of the carpet overlocked at my local carpet place.

carpet2.JPG

And we're done.

@The scissor jack can still be easily accessed even with the false floor.

@The rear struts can be removed without having to remove the lower level of the false floor.

@Total loss of boot volume is apprx 70 Litres (floor raised by approx 8.5cm)

@Total cost approx $90 for wood carpet etc..

@Took about 5 days to do (about 3 -4 hours a day) Ant and I spent alot of time leaning over the boot and staring aimlessly, pondering, day dreaming, :bored2dea :confused: etc.... Someone more focused could probably do it in a day :)

Edited by Fanta R33GTR
Link to comment
https://www.sau.com.au/forums/topic/190711-project-false-floor/
Share on other sites

Ditto to the bracing! =-o

So, a question for you...

What supports the MDF in the middle (over the spare tyre)? I did a VERY similar setup but over time the floor started to sag horribly. Laptop, shopping... nothing majorly heavy went in there.

Also, how did you mount the MDF to the floor?

Cheers!

Ditto to the bracing! =-o

So, a question for you...

What supports the MDF in the middle (over the spare tyre)? I did a VERY similar setup but over time the floor started to sag horribly. Laptop, shopping... nothing majorly heavy went in there.

Also, how did you mount the MDF to the floor?

Cheers!

The middle MDF is supported on the left side by the amp base and on the right also by the false floor base. To stop it sagging I have run 2 pieces of 2cmx2cm square aluminium tubing along the backside of the middle piece (in the photo's you can see 2 lines of screws that run along the middle piece, these fix the aluminium to the mfd) You can put enough weight on this setup to push the suspension on the car down without any sag. I used 9mm MDF. The middle board clears the cap by about .5cm, no weight is supported by the cap.

Mounting the MDF to the boot floor without making any unreversible changes was a real challenge.

The left side (amp) - There are 2 bolts that come up throught the floor. They are holding up the heatsheild for the muffler. I replaced these bolts with longer ones to give me something to bolt the floor base to.

Right side - On this side also there are 2 small bolts that come up through the floor. These are not long enough to mount the board onto, so I made up a metal plate that bolts onto the existing bolts. The plate has longer bolts attached to it so I can mount the floor to it.

I know it sounds a little confusing.. i'll upload more pics to clarify tomorrow.

Edited by Fanta R33GTR

thats an awsome design man, just 1 question or thing id be orried about, how does the amp hold up without air around it. The reason I ask is cause ive had an amp catch fire before, it was a shit amp and not the best instalation (just got my licence, older and wiser now hopfully :) ) but it was placed under my drivers seat so i smelt it before anything bad could happen, and i thought mayby extra dust and lack of air circulating might have been a contributing factor.

thats an awsome design man, just 1 question or thing id be orried about, how does the amp hold up without air around it. The reason I ask is cause ive had an amp catch fire before, it was a shit amp and not the best instalation (just got my licence, older and wiser now hopfully :thanks: ) but it was placed under my drivers seat so i smelt it before anything bad could happen, and i thought mayby extra dust and lack of air circulating might have been a contributing factor.

Thats the reason why I went for a very well known brand of amp. The P4004 has a huge heatsink surface and plenty of heatsink mass. I've measured the temp, using a infared thermometer, after a 90min drive with the music pumping and the hottest part on the heatsink was only 32deg, so even in summer I don't expect the amp to get above 40deg.

I was initally going to go with the jaycar 100x4 amp, but it's more compact and runs much hotter.

Very impressive!

I want your original amp/sub setup you have there. What sub do you run? And what are the dimensions of the amp mounted next to the battery? How do you get it in and out?

amp12.jpg

The sub is an 8" Kicker square sub. It provides around th same punch as a 10" or 12". It's a dual coil sub so it's a little more expensive but needs less volume. the volume of the sub is around 30 litres and molded to fit around the computers in the boot.

The amp is a Alpine 350

Dimensions

Width 9.5 in.

Depth 10.5 in.

Height 2.31 in.

It's actaully really easy to get the sub and amp in and out (after you've undone the 20 or so bolts for all the rear bracing and struts) :thanks:

sub.JPG

Edited by Fanta R33GTR
my bad, does it actually do any bracing? and is it transferrable to a GTS?

nice work on the false floor it looks stock, been meaning to do something like this.

That bracing does add a little stiffness, but is only a real advantage if your driving hard.

It won't straight into a GTS, but you may be able to modify it fit in. Not sure.

The middle MDF is supported on the left side by the amp base and on the right also by the false floor base. To stop it sagging I have run 2 pieces of 2cmx2cm square aluminium tubing along the backside of the middle piece (in the photo's you can see 2 lines of screws that run along the middle piece, these fix the aluminium to the mfd)

The left side (amp) - There are 2 bolts that come up throught the floor. They are holding up the heatsheild for the muffler. I replaced these bolts with longer ones to give me something to bolt the floor base to.

Right side - On this side also there are 2 small bolts that come up through the floor. These are not long enough to mount the board onto, so I made up a metal plate that bolts onto the existing bolts. The plate has longer bolts attached to it so I can mount the floor to it.

Ahhh... Nicely done!

So the square tubing (of which I have plenty!) is screwed to the MDF.... but stops before the edge? That overlap would sit on the raised sections of the amp and floor mounts, then get screwed in? No.. not screwed in? You couldn't get to your tyre if that was the case. Thanks for the explanation! (and good luck pulling those hard disk magnets off the spare!!!) =-D

  • 9 months later...
  • 4 months later...
  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Cheers. Skyline is back on the menu, can’t get rid of it. It’s like a child you don’t want, or herpes 
    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
×
×
  • Create New...