Jump to content
SAU Community

Recommended Posts

Im no HeKitC KrNt but on a serious not. Apart from f**king you turbo in the long run, its there a down side to this. A few of my friends who was set their cars up for drift have blocked up their BOV's. I never thought to ask them why...Is there any particular reason for this?

Edited by Lock_to_lock

omfg you want some dose uleh?

You'll be a fully sick hectic bro, and all the women will get instantly wet when they hear the tuutuuutuuutuuut and dive in your windows just because they think its all fully sic bro uleh bling.

Then all you need to do is have a big mofo rocket switch, so that you can rig up some fully sic atmospheric blow off valves, so when you had enough of the fully sic tuutuuutuuutuuutuuutuutuuutut you can make it go WHOOOOSH. (cough, stall, omg uleh, etc)

The atmospheric BOV will be even more fully sic, and you'll need to fit bigger windows because there will be more womenz getting fully sic and wet and trying to dive into your car.

Then wehn you have too many women, you can turn it back to some fully sick dose.

apparantly blocking off the bov will give u less lag, thats the only advantage i believe

im horrible at explaining things but thats a load of poop. if anything, blocking your recirc valve or not running one, will slow the turbo down at a much faster rate. although its been proven that you can 'boost spike' it for a second apon an extremely fast gear change. Basically you have to be quick enough to change gears before the already built up boost pressure escapes through your filter, if you can do that and open your TB back up in time, its more inclined to throw the boost through your intake rather than out through the turbo because the blades are already spinning that way, and its the easiest direction for the air to flow. So say your usual 10psi of boost, supposively you may spike it to 13psi for a split second after your gear change. ive read about various WRC cars using this technique.

I think this is where people get the misconception about it cutting a bit of lag.

anyway, i told you im horrible at explaining things but i hope that makes atleast a little sence. :P

just thought a little more in to that, and i missed the obvious. What i explained, IF you can change gears fast enough, it WILL cut back on the lag. im not thinking straight tonight. sorry mark.

atleast i was able to explain the theory a little :P

Curious to know for it to flutter, Do you just block the plump back pipe? or do you completely remove the bov and block everything? as a friend asked and I couldn't give him a proper answer because I have no clue, A apexi pod filter is plenty of whoosh for me :P

Bro..................i put my skyline on it, it will annoy the crap out of you with in a month

and you would wanna take it off.......................

Lol btw...........im leb and i hate that sound. uleh

lol

omfg you want some dose uleh?

You'll be a fully sick hectic bro, and all the women will get instantly wet when they hear the tuutuuutuuutuuut and dive in your windows just because they think its all fully sic bro uleh bling.

Then all you need to do is have a big mofo rocket switch, so that you can rig up some fully sic atmospheric blow off valves, so when you had enough of the fully sic tuutuuutuuutuuutuuutuutuuutut you can make it go WHOOOOSH. (cough, stall, omg uleh, etc)

The atmospheric BOV will be even more fully sic, and you'll need to fit bigger windows because there will be more womenz getting fully sic and wet and trying to dive into your car.

Then wehn you have too many women, you can turn it back to some fully sick dose.

point proven.. this ladies and gents is what we call a douche bag..

the whole point to this exercise is for me to learn a bit more about my car and f**k around with it and not really have to spend money..

as for the attuides on the forums most have been nice to try to help me with any queries.. for the rest with the flame wars tryin to stir shit its just sad.

all i wanted to kno was ( if its possiable, how would i go about it, where there any issues with it and half the fknin posts are dick heads actin like the scum of the earth, im sorry but you are on a even playin field with all those penis hair cut c**ts.

And thank you to all that answered my question

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Try looking at Eibacb/H&R springs Thats what Gary sourced for mine.
    • Hey y'all! I'm curious about how y'all go about widebodying your cars. I noticed that when running a square setup, my front wheels are a bit more tucked in than my rear wheels. Not by much, maybe 5-10mm. This leads me to wonder - when I widebody, should I use narrower front flares and wider rear flares? I found a set of 40mm rear flares that I really like, and was thinking of pairing them with some 18mm front flares, but I don't want the car to look strange. How have others done this? Note, I'm in a sedan. Thanks!
    • And if it was anything other than an auto tranny part, it might be a problem. But seeing as all auto trannies belong in the recycling bin, it's fine.
    • I have an R32 Fenix rad. It is good.
    • All the schemas I can see, indicate your typical setup of ATF 'cooler' (read: heat exchanger) in the bottom radiator tank..ie; https://nissan.epc-data.com/stagea/wgnc34/5413-rb25det/engine/214/ ...but I can prattle on a bit here. These trannies have a thermistor in the sump ~ the TCU reads this and 1. bumps the line pressure up when the ATF is 'cold' and 2. prevents the TC lockup clutch from operating, until the ATF comes up to minimum operating temp (keeps the ATF 'churning' through the TC so it heats up quicker) -- trigger point is around 55C. In these conditions, the engine coolant temperature rises faster than the ATF temperature, and also helps heat the ATF up, which is why it's best to think of the in radiator tank setup as a heat exchanger ; the heat can flow in both directions... ...with these trannies, the 'hot' ATF comes out the front banjo bolt, flows through the cooler/heat exchanger, and returns to the box  via the rear banjo bolt. This gets a mention, due to the wildly different opinions wrt running auto trans fluid coolers ~ do you bypass the in radiator tank altogether, or put the cooler inline with the in radiator tank system...and then, do you put the additional cooler before of after the in radiator tank system?... ....fact is the nominal engine operating temp (roughly 75C), happens to be the ideal temperature for the ATF used in these trannies as well (no surprises there), so for the in radiator tank system to actually 'cool' the ATF, the ATF temp has to be hotter than that...lets say 100C -- you've got 25C of 'excess' heat, (slowly) pumping into the 75C coolant. This part of the equation changes drastically, when you've got 100C ATF flowing through an air cooled radiator ; you can move a lot more excess heat, faster ~ it is possible to cool the ATF 'too much' as it were...(climate matters a lot)... ...in an 'ideal' setup, what you're really trying to control here, is flash heating of the ATF, primarily produced by the TC interface. In a perfect world, wrt auto trans oil cooling, you want a dedicated trans cooler with builtin thermostatic valving - they exist. These should be run inline and before the in radiator tank system ~ when 'cold' the valving bypasses the fin stack, allowing the ATF to flow direct to the in radiator tank heat exchanger, so it works 'as intended' with helping heat the ATF up. When 'hot' (iirc it was 50C threshold), the valving shuts forcing the ATF through the cooler fin stack, and onto the in radiator tank heat exchanger...and you sort of think of it as a 'thermal conditioner' of sorts...ie; if you did cool your ATF down to 65C, the coolant will add a little heat, otherwise it works as intended... ...the 'hot' ATF coming from the front bango bolt, is instantiated from the TC when in use, so all/any flash heated oil, flows to the fluid-to-air cooler first, and because of the greater heat differential, you can get rid of this heat fast. Just how big (BTU/h) this cooler needs to be to effectively dissipate this TC flash heat, is the charm...too many variables to discuss here, but I just wanted to point out the nitty-gritty of automatic trans fluid coolers ~ they're a different beastie to what most ppl think of when considering an 'oil cooler'... /3.5cents   
×
×
  • Create New...