Jump to content
SAU Community

Recommended Posts

Hi....

Ive recently got an R32 GTR and was wondering if you guys notice a dramatic different in the power on say a 30 degree day vs a really cold night...

On a hot day it seems very sluggish in comparison....

How much power would you estimate is lost on a very hot day vs a cold night...

Thanks

Ashley

Link to comment
https://www.sau.com.au/forums/topic/193965-power-lost-on-hot-days/
Share on other sites

HEAT SOAK!

Yeah it makes quite a bit of difference for me, I can normally bang in just under a bar of pressure on a cold night, but I won't see past ten PSI on a hot day...

Get some Cold Air Induction and it should do better :rofl:

i think it was a reduction in power of around 1-2% for every 5 degrees the inlet temp goes up. but don't quote me

the main thing you'll notice in super cold weather is sharper throttle response and more low to midrange torque. in fact, the engine is more likely to suffer pre-ignition in really really cold conditions as the charge density at the point of peak torque will be much higher than usual (MAF based ECUs account for this though, and trim the spark advance accordingly)

My understanding is that air is more dense on a cold day there for a better quality of air so ur A/F ratio's are more stable resulting in more power, On a hot day the density reduces causing a loss of power. Don't quote me thogh i could be wrong.

FWIW, here's a definition of heat soak from here. This is why you use a turbo timer, it has nothing to do with loosing power on a hot day.

"When the engine is switched OFF, the cooling system becomes inactive and the residual heat in the engine from the block, head and exhaust manifold are transferred to the coolant and other engine components. The engine temperature actually increases after a hot engine shutdown. This is called 'afterboil' or 'heat soak' and can be damaging to engine life."

No, the heat soak I meant was not getting enough cool air flow to the air intake...

You're talking about something different...

In 32 GTRs the air intakes are tucked pretty high up without a snorkel, so they can heat soak pretty well... the hotter the air, the less dense it is, so the less air that can fit into the cylinders... And without proper cold air induction, it sucks in all the hot air from the engines radiant heat...

And i dunno about you, but I use a turbo timer for the TURBO to cool down, it's not called an engine timer now is it? :rofl:

My understanding is that air is more dense on a cold day there for a better quality of air so ur A/F ratio's are more stable resulting in more power, On a hot day the density reduces causing a loss of power. Don't quote me thogh i could be wrong.

Very close, the air is more dense on a cold day, so the engine management adds more fuel to maintain the correct A/F ratio, and you make more power because you're burning more fuel. And vice verca so less power on a hot day.

No, the heat soak I meant was not getting enough cool air flow to the air intake...

I've never heard that referred to as heat soak before, but maybe i need to get out more. Google for heat soak and you'll see what i mean.

In 32 GTRs the air intakes are tucked pretty high up without a snorkel, so they can heat soak pretty well... the hotter the air, the less dense it is, so the less air that can fit into the cylinders... And without proper cold air induction, it sucks in all the hot air from the engines radiant heat...

My stock 32 GTR has a factory snorkel....so it doesnt pull any air from the engine bay YMMV.

And i dunno about you, but I use a turbo timer for the TURBO to cool down, it's not called an engine timer now is it? :rofl:

You're being a bit to literal :-)

Heat soak refers to what happens to the intercooler, i.e when the intercooler cant cool the air enough any more because its aluminum fins are heat soaked with well heat.. typically happens at traffic lights where the car can take on a shitload of heat.

The CAI system can also take on this but typically refers to the SMIC.. thats why a FMIC is alot better as the air charge is cooled much more efficently. hence why I bought the screwball thing

Edited by DECIM8

Heat soak is this, heat soak is that, nooo heat soak is this.

My goodness. Heat soak can mean heat soak on anything. It is as it states, soaking up heat. It doesn't have to be the pod or the motor or the intercooler. Heat soak can occur on a glass bottle in the sun, heck sponges suffer heat soak in hot water.

The terms should of been mentioned "heat soak of the _____".

Edited by KeyMaker
Very close, the air is more dense on a cold day, so the engine management adds more fuel to maintain the correct A/F ratio, and you make more power because you're burning more fuel. And vice verca so less power on a hot day.

BINGO!

The basic idea of an engine is to ignite an air/fuel mixture and produce power. The more air we can get into a motor, the more fuel we can add to it, the more air/fuel mixture the more power we make. When temperatures rise air becomes less dense (less air in any given space), obiviously when temp decreases air becomes more dense (more air in a given space). Thats why on cold nights (when the car effectivly get more air) we get more power, and on hot days (car effectivly gets less air) we lose power.

:ph34r:

How much power would you estimate is lost on a very hot day vs a cold night...

Depends on setup. When my R was stock, it felt like 25% lol... serious

Yeah it makes quite a bit of difference for me, I can normally bang in just under a bar of pressure on a cold night, but I won't see past ten PSI on a hot day...

Hence, the usefulness of EBC's

i try to keep away from the whole 'boosting' thing on a hot day

I never like this idea. Performance is total. What if it was 390 on a well planed track day? Would you baby your car? Thats for aftermarket (or PFC) knock sensors are for (not to mention human ears) I reckon the idea's to tweak your inlet temp correction to counter hot days. End results are end results, anything you can make compared to the guy next to you, is a profit smile.gif

this is where high quality coolers etc come into their own and shitty ebay bar and plate coolers start to sap power.

Trent, wasn't there a time, when bar and plate coolers where deemed superior to tube and fin? AVO's 1000hp coolers are still bar and plate... as are upper echelon HKS IC's i believe.

FWIW, here's a definition of heat soak from here. This is why you use a turbo timer, it has nothing to do with loosing power on a hot day.

"When the engine..."

For the purposes of the performance arena, i think "heat soak" refers to when the devices that are meant to move heat from intake air -> IC -> ambient air work in the opposite. This is noticeable in stand still traffic, where a IC can introduce ambient temps BACK into the IC -> intake air. This applies of course to intake piping and plenum's etc. F_ck Google.

My stock 32 GTR has a factory snorkel....so it doesnt pull any air from the engine bay

Meh to stock, 400rwkw+ deems AM pods and a proper CAI necessary for street application (im sounding like a c_nt tonight, must the the multiple personalities) :(

: To answer your original question, i think R's suffer from heat soak more then others, due to the surface area of all the piping. Twin turbos, twin intakes, twin filers, twin manifolds etc. My R when stock felt like a dash mounted marshmallow after a stand still period. Proper CAI's, bonnet vents etc help, but even after you have tweaked all your inlet temp correction values, you have to accept more heat means less power. You can imagine then why 5mins cruising in 5th at 80km/h in 50 weather has such a profound effect on throttle response and mid range (due to the ignition advance the ECU winds into (or should) in those conditions)

read into it, what you will loler'NZ-bungie jump

Edited by GeeTR

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
    • Just like in being 14mm too small (296mm) makes it not fit, being 14mm too big (324mm) it also won't fit. You want to find the correct rotor.
    • @GTSBoy Ok so that was the shops problem...they showed R33 rotors on R34 page and i did not know 296 do not fit(and are for R33) Yes i bought "kit" with rotors and pads. Pads are ok(i have GTT calipers front and rear). They have some 324mm but no 310mm. So i dont know if they would fit. I have 17inch LMGT4s So another question. Can i fit those in the rear or they are just "too" big for that?
×
×
  • Create New...