Jump to content
SAU Community

Recommended Posts

Hey everyone

I have a bit of a problem, and i dont know how its happened :)

One night (friday nite), when i went to go start my car, it just struggled.

Sounded like it was running on 5 cylinders and after few checks its exactly what it was doing.

I took each plug out while the car was running and cylinder 3 just wasnt doing anything. eg) while the car was on, i removed cylinder 1 coil pack plug out; it will drop a cylinder, however number 3 just didnt do anything (remained the same)

I changed the coil pack from say cylinder 2 to 3, and still cylinder 3 does nothing.

I put the coil pack against the block and started the car to see if there was any spark, but didnt notice anything..

I really dont think theres anything wrong with my coil packs, but perhaps the wiring loom itself..

So i got the multi meter out, but after doing a few tests, it just seems like theres no voltage going to coil pack 3.

Theres nothing wrong with the spark plugs (cylinder 3 plug is a little black-but i guess due to the fuel being dumped into it while the car is turned on)..

Took stock ecu out and plugged in my power fc and still cylinder 3 doesnt fire.

Its just cylinder 3.. All other cylinders seem fine.

Has anyone else experienced this before? Any help/advice is much appriceated.

Only thing i can really do is to borrow someones wiring loom and connect it up to see whether it works. If anyone in sydney is willing to help me out please do let me know :ph34r:

Cheers

ps- if you need any more info let me know.

thanks

edit: mods for my car are: full exhaust, pod filter, r34 cooler, stock ecu/turbo.. nothing else!! I dont really see how this will affect it, but just giving as much background info as possible. Also spark plugs are coppers re-gapped to 0.8 (been using it for 1.5 years now- changed every 5000kms)

Edited by siddr20
Link to comment
https://www.sau.com.au/forums/topic/195945-cylinder-3-just-isnt-firing/
Share on other sites

If there's no spark and the problem stays with cylinder 3 despite swapping coils about then i think you are right that it's a wiring problem. (assuming you have no igniter based on your car being an s2)

The last thing to check before delving into wiring is the spark plug. Swap it with another one to be sure

As far as the wiring goes, all coils have a common power, a common earth and an individual trigger.

So you have determined you have no power to the coil, i assume by searching for 12V? just as a check before stripping back the loom, check for continuity from the power plug to all of the coil plugs. If 3 shows nothing then you just need to strip that section back and find the break in the wire.

i really aint confident stripping those wires back and checking if theres is a broken state somewhere.

See the thing is, it just happened out of know where.. Not like i was mucking around with anything etc..

I was helping Sidd with this last night. It appears its only one of the wires on #3 going to the igniter, not the ground or the other one, but the pink one which is the trigger wire that is coloured different for all 6 coils. That was the one that wasnt reading the voltage. Guess the best bet is to swap the look going to the igniters and see how we go? If its not that, then its got to be the other half of the loom going to the ECU id presume...

Alternatively as a ghetto fix, could I just tap into the wire off another igniter from say #4 ?

Dave, it is the individual trigger that doesnt read the voltage.

Edited by Mr_G

Definately cant hook it up to another pin on the igniter. If you have a scope, hook that up to the wire in question, it should be a switched earth, ie the igniter pulls the voltage to ground. Have you tried swapping the igniter for another one?

You won't get to read a voltage on that wire unless you have a CRO

It is a VERY short burst to trigger the coil to ignite (I beleive it grounds it actually.)

You would need to look at the wave form on a CRO to see if anything is happening.

Have you done a compression check?

Don't just immediately blame electricals. So far the check you have done is inconclusive.

I had my #3 cylinder drop out when my CAS started clogging up with dust from a blown bearing in the cas itself. Was a pain in the ass to find the problem.

Could be worth taking the CAS off and making sure it spins freely (should spin very very easily with no noise at all) or if you can open yours blast some contact cleaner through it.

You can also check if your ignitor is working with a parker globe, just touch the legs on the + and - of the coil pack connection and see if it lights up at all. It should just be a dim flicker. Either that or buy a cheap multimeter that can measure frequency and check it that way.

Have you done a compression check?

No i havnt.. Perhaps tomorrow night after work i can do it.

But im sure the compression will be healty across all cylinders.

If theres no voltage or spark coming across the wiring loom to that cylinder then logic just says, theres something wrong with that wiring to plug 3. Since all other cylinders are getting voltage etc.

Well mbs206- i really dont know what else to do in terms of testing by myself.. Dont really have much tools etc etc..

I think i might just borrow someones wiring loom - atleast im narrowing it down if it works or not..

frost- so howd you find that out tho? might give that a go too then.. worth hurt if i cant find the problem

Edited by siddr20

If you are 100% sure you don't have spark on number 3 then check all electricals . Try this very easy test : Take number 3 spark plug out and connect the coilpack back on it, take a multygrip or anything else that is well insulated ( otherwise you will get a belt) and while you are grounding the spak plug on the cyl head, someone can crank the engine , then you will know for sure if you don't have spark.

didnt understand what you meant sorry.

So take spark plug out and connect the coil pack back on it?

So what am i doing with the multigrips? holding the spark plug against the coil pack and seing if theres a spark??

im totally lost as to what you meant sorry..

Well i have put the coil pack against the block and cranked the car, but i couldnt see any spark coming out of it..

Also i have swapped coil packs from cylinder 3 to 2 and it works.. So nothing wrong with my packs..

Spark plug out , fit the coil pack on to it as if it was in place, ( you don't need to hold the plug on the coil pack it will hold by itsef) this way if all works the plug should fire across but it must be grounded as you need + and - . The reason you need insulated muti-grips to hold the assemby ( plug with coilpack), if all works you will get a belt. How else would you hole the plug on the body of the cyl head , if you use your hand you will get a belt!!

dont even have to take a plug out, find any old 2nd hand plug and hook it up to the coil pack. make sure the electrode is earthed on the motor somewhere and then crank it over, if it doesnt spark you have an issue, if it does spark then i would say the injector is an issue. best way to test this is with an LED test light, The injector plug (probe it while cranking) should have pulse on one of the wires. If its pulsing then you can eliminate it to a dud injector. If no pulse then your injector wiring needs attention.

if you have no coil pack spark, and you have tried swapping the packs... then i would say its a broken wire in the coil pack loom somewhere

No i havnt.. Perhaps tomorrow night after work i can do it.

But im sure the compression will be healty across all cylinders.

If theres no voltage or spark coming across the wiring loom to that cylinder then logic just says, theres something wrong with that wiring to plug 3. Since all other cylinders are getting voltage etc.

The only multi meter I can think of off the top of my head is the Fluke 87 to detect if you have spark, as it has a min/max range.

The time that the pulse is for, is VERY minimal, and the gap between pulses is MUCH MUCH larger then the gap of the pulse.

Hence, a multimeter (Average one) will just read 0V whilst that wire is pulsing away.

Try hooking a led light with resistor in series with it across the + and - terminals and see if it is dimly lit (Use aronud a 600 Ohm resistor in series with the led light.)

Also make sure you hook the led light up in the correct orientation to avoid blowing the led light.

But you MIGHT be able to see a dimly lit led light this way. (This is also a slightly inconclusive test as you may not see it, but it's still pulsing)

The only true way is to use a CRO.

Also do a resistance check from one end of the loom to the opposite end of the wire. If the reading is < 0.7Ohm, the loom is fine.

The advantage of using the plug in #3 is that you may be able to observe any damage to the electrodes, such as might be caused by a chunk of piston playing pin-ball inside the cylinder and combustion chamber (been there, done that!)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • OK, Step 3, if you need to remove the valve body, either to replace it, the TCM, or to do a more complete drain.  First, you need to disconnect the TCM input wires, they are about half way up the transmission on the drivers side. One plug and the wires are out of the way, but there is also a spring clip that stops the socket from sliding back into the transmission. On my car the spring clip was easy to get, but the socket was really stuck in the o-ring of the transmission housing and took some.....persuasion. You can see both the plug to remove (first) and the spring clip (second) in this pic Incidentally, right next to the plug, you can see where the casting has allowance for a dispstick/filler which Nissan decided not to provide. there is a cap held on with a 6mm head bolt that you can remove to overfill it (AMS recommend a 1.5l overfill). Final step before the big mess, remove the speed sensor that is clipped to the valve body at the rear of the box.  Then removal of the Valve Body. For this the USDM Q50 workshop manual has a critical diagram: There are a billion bolts visible. Almost all of them do not need to be removed, just the 14 shown on the diagram. Even so, I both removed one extra, and didn't check which length bolt came from which location (more on that later....). Again it is worth undoing the 4 corners first, but leaving them a couple of turns in to hold the unit up....gravity is not your friend here and trans oil will be going everywhere. Once the corners are loose but still in remove all the other 10 bolts, then hold the valve body up with 1 hand while removing the final 4. Then, everything just comes free easily, or like in my case you start swearing because that plug is stuck in the casing. Done, the valve body and TCM are out
    • OK, so if you are either going for the bigger fluid change or are changing the valve body which includes the Transmission Control Module (TCM), first you should have both a new gasket 31397-1XJ0A and a torque wrench that can work down to 8Nm (very low, probably a 1/4 drive one). You can probably get by without either, but I really didn't want to pull it all apart together due to a leak. First, you now need that big oil pan. The transmission pan is 450 long x 350 wide, and it will probably leak on all sides, so get ready for a mess. There are 24x 6mm headed bolts holding the pan on. I undid the 2 rear corners, then screwed those bolts back in a couple of turns to let the pan go low at that end, then removed all the middle bolts on each side. Then, undo the front corner bolts slowly while holding the pan up, and 80% of the fluid will head out the rear. From there, remove the remaining bolts and the pan is off. You can see it is still dripping oil absolutely everywhere...it dripped all night.... I got another couple of litres when I removed the pan, and then another few when I removed the valve body - all up another 4l on top of the 3 already dropped in step 1.
    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
×
×
  • Create New...