Jump to content
SAU Community

Recommended Posts

Got my 120 degree intake made up yesterday, fitted it today, seems a hell of a lot more responsive (had to be careful, pissing down out here). Need to get my BOV adjusted properly yet, every now and then when pulling up it stalls, and yes its a plumb back. What is the best way to adjust it?

1st pick shows with original.

post-536-1196664316_thumb.jpg

2nd pick shows both side by side, alot of piping taken out.

post-536-1196664389_thumb.jpg

3rd pick shows new pipe fitted up. Even looks alot better.

post-536-1196664438_thumb.jpg

Photos were taken with my phone, i left my camera at home, did the job at work.

Link to comment
https://www.sau.com.au/forums/topic/196148-120-degree-intake-pipe/
Share on other sites

i think it would make a difference. he's eliminated 2 sharp-ish bends which will cause a bit of turbulance and restriction. the last bend is open in terms of the angle.

i like the design. to get to your last 3 plugs you need to take the crossover pipe off anyway. at least now its only a matter of 2 clamps and you can swing it around. the oil filler cap will be a bit of a problem though.

I'll be going for exactly this kind of setup in about a months time. SydneyKid and a few others recommend it. RE in the way of the sparkplugs/coils - the only piping I've seen that isn't is a forward facing plenum, any other aftermarket IC piping is also in the way and has to be taken off for work. I'll be trying Hypertune's kit, apparently it's 5 piece.

Oil filler cap isn't that big of a problem

I have a pipe much similar to that

When I'm doing oil, I'm doing plugs at the same time, so that pipe is off!

If I needed to "top up" you can still get the cap off easily enough.

Bonnet isnt as problem and i can live with the oil filler cap, 2 clamps and its off. I think it even looks better. Intake temps have dropped a little as well, i monitor those with one of those jaycar temp probes.

Also, Wolverine: That's the exact same one I run. I don't find hose clamps are needed to be loosened at all.

they might have modified the kit slightly, i got mine a while ago. mine fowls slightly so loosening the clamps is enough to unscrew the cap.

or possibly the location of the cooler is different on yours which lifts it up the few mm's to clear the cap?

Edited by wolverine

just throwing it out there.

wouldnt it be more beneficial to get a forward facing intake plenum.

im installing one atm and it gets rid of almost 2m of piping and looks clean.

nice and clean. u can access the engine block without all the piping in the way

Edited by r33cruiser

plenum=200-400 ebay

bolts, nipples etc=20

xf TB= 50 ebay

270-470. and is a long term fix with greater benefits.

labour costs=NO

=diy

http://www.skylinesaustralia.com/forums/to...um-t181826.html

Edited by r33cruiser
Another negative comment, didnt get any last night ay?

:)

Don't get me wrong.

It's the design I would do from the start if I was doing a fmic.

Gibson motorsport used this on the race R31's..

I just wouldn't have bothered if it already had the U shape across the motor like he already had.

each to their own.

had to do this too, as my turbo was in the way of the stupidly wide arc made by the original piping. i dont think i want it close to the exhaust anyway

i dont like the look of it tho, so will go some sort of front facing plenum eventually

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...