Jump to content
SAU Community

Mate Ran Up My Ass, Whats A Good Panel Beater?

UNR33L

By UNR33L,
in Victoria

 Share

Recommended Posts

UNR33L Grand Master

UNR33L

Posted
Posted

Hey guys long story short, i was coming out of maccas turning onto burwood hwy i was stopped, he must of thought i was going (wasnt tho cos car in left lane on burwood hwy) ran into my ass while i was standing still, fair bit of force knocked the boot out of wack a littlebit and broke all the clips n stufff on rear bar - boot (boot wont close rear bar still in fairly good nick tho) and its generally warped a littlebit and uneven, oh and a little crack on my brake light.

I live in Wantirna (SE Suburbs) and yea just thought you guys would know of a good place

thx, leigh.

Helio Proficient

Helio

Posted
Posted

These are some of the better I know of. If you search "panel beater" down the bottom of the vic page then you will find more. Good luck.

DT Panels

12 Lightwood Drive Springvale

Call Vu 0402611670

MiColour - Dissik St.

Cheltenham

Mick - 0419153283

UNR33L Grand Master

UNR33L

Posted
  • Author
Posted
These are some of the better I know of. If you search "panel beater" down the bottom of the vic page then you will find more. Good luck.

DT Panels

12 Lightwood Drive Springvale

Call Vu 0402611670

MiColour - Dissik St.

Cheltenham

Mick - 0419153283

thx for the mate

ne1 else got anymore they'd like to add that are good price and do good work on imports?

~R33AzzA~ Proficient

~R33AzzA~

Posted
Posted

I would give stud park panels a call they have a realy high standards. My mate took his 4 door 33 there after some guy put a tow bar throgh his door and damaged the quater and it looks great now.

DogKnight Mentor

DogKnight

Posted
Posted (edited)

I used Imperial Finish Body Works. They are on Centre RD, right near the intersection with princess hwy and springvale rd. When I hit a fire hydrant and had some fairly bad damage to my front right quarter, they did excellent work. Was really happy with the work. My mate also had work done there on his R32 GTR when he was rear ended badly. His whole boot, rear bumper, etc was bad and it looked brand new when done. No problem recommending them.

#

Imperial Finish Body Works

# 1652 Centre Rd Springvale 3171

# (03) 9547 8111

PS: Dont know how good he is on pricing as it was an insurance job, but his work is worth it. And my sig photo is the car after repairs, the front right.

Edited by DogKnight
BRUNSKIGTST Proficient

BRUNSKIGTST

Posted
Posted (edited)

Call Aron

0408 325 517

he owns breos pannels in Dande he did my 2 quarters on my R32 skyline replaced GTST with GTR everyone been saying he did a Top notch job really stright no and fixed major rust stop replaced a pannel in my boot paid 1500 for both quarters and other small jobs to my car

He will do the job just tell him Bruno told me to give u a call and that you replaced his quarter pannels on his R32 skyline and he tell ya where he is and stuff and give ya a quote he really nice guy became good friends in the end :banana:

Edited by BRUNSKIGTST

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • JC71
      98 R34GTT 4k engine stumble

      By JC71 · Posted

      neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • TurboTapin
      Why am I hitting a power wall with my stroked RB25?

      By TurboTapin · Posted

      Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Dose Pipe Sutututu
      Why am I hitting a power wall with my stroked RB25?

      By Dose Pipe Sutututu · Posted

      Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
    • MBS206
      RB25DET with solid lifters - which cams ?

      By MBS206 · Posted

      Shimmed or shimless, still solid, no hydraulic pump up stuff.
    • MBS206
      NC MX5

      By MBS206 · Posted

      They have said food will be limited. Mainly meat pies and sausage rolls from memory. But they have a coffee van!
×
×
  • Create New...