Jump to content
SAU Community

Recommended Posts

$10 per kg pretty much. Though as you can see diff protein contents - my point being, realistically if I'm going to see any difference from the lower protein amount given my workload. I'm guessing not.

post-23873-0-54612000-1369709826_thumb.jpg

Ayo if you don't care about mixability and lactose, go the concentrate. Personally I can't stand unmixed shit, so I like the isolate. I also have a slight aversion to too much lactose.

Okay, well that will certainly mix easier than the concentrate...but meh...get a sample or a 1kg bag of the concentrate and see what it's like?

I go through this stuff fairly quickly, so even a 5kg bag of a bad flavour or something doesn't phase me.

Ayo if you don't care about mixability and lactose, go the concentrate. Personally I can't stand unmixed shit, so I like the isolate. I also have a slight aversion to too much lactose.

I find concentrate mixes fine, have had a few brands no clumps. Just don't be lazy and only shake it 3 times.

Edited by Mangune

Either way (including calcium cassinate), easiest way to mix is with a stick blender in a tall cup , I do oats plus frozen blue berries as my breakfast with some non flavoured pure protien. Simple clean up and ready in seconds.

Concentrate is slightly slower to digest vs isolate (both are rapidly absorbed however , so work as post workout pretty well). If you don't care about taste ,Concentrate is the way to go.

ive gone off pretty much all supplements. Only the occasional pre workout if i am real run down after work.

otherwise its just food food food for me. Getting pretty tired of eating chicken, fish and steak though...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
    • Yes then it will turn on but I want the car features to work  
    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
×
×
  • Create New...