Jump to content
SAU Community

Recommended Posts

My Filtermag arrived today from the USA, probably not really worth posting about, but since I wasnt able to find one in Australia I figured I would anyway. The concept is that your oil filter cannot phyically filter out all of the metal shavings produced as part of engine operation. If it could, the filter would have to be so fine that Oil itself couldn't pass through. Instead, the fine iron particles are attracted to the the magnet and removed from the oil circulating through your engine. I tested it on a spare oil filters in the garage and damn it's a powerful mofo! once that b1tch is on it won't come off too easily!

Has anyone else tried them out? Comments?? etc?

cimg1542bh6.jpg

So this goes AROUND the outside of the line or something, still leaving the metal in there, just collecting enough of it together, that when you finally take it off, you have a ball bearing of metal ready to be sent through your engine? Or if you leave it on, you have a clog...

Is this correct?

Cause if it is, it sounds like fun :(

I'm guessing it would accumilate in the filter, then when u change filter take it off and turf the shrapnel with it, then put it over the new filter.

Good idea.

Haha well I bought it specifically for whilst running in my new motor, I also have a magnetic sump plug, the g/f's dad has one one of the plugs his Gen III which picks up alot of cr@p too.

Edited by MintR33

Sure mate, I got it from ebay off this guy: Ebay Member

And the product website is: www.filtermag.com

If I remember correctly the website has alot of pics of filter's cut in half... take them as you will, no doubt they only posted pics with the largest build up of fine iron, but in all honesty I can't see how it wouldn't work, since the dirty oil passes through the outside of the filter past the magnet before being pulled through the filter core. I've also heard that the A'PEXi UFO filters use a magnet aswell. The benefit of this one is that you can swap ot over to your new filter with every oil change.

not a bad idea on a new engine since everything is wearing in but i see it doing close to nothing on a engine that was already "run in".

If your engine was turning around metal that is able to be picked up by a magnetic, you have more things to worry about than oil filtration.

SnakOil my ace, ppl run magnetic sump plugs for the same reason. Here you have much more powerful rare earth magnets (i would assume) right where the oil is already turbulent and full 'o' eddys.

Check the site, theres something being picked up by the magnet thats gettn by the filter.

These are absolute gold, one of those "cant believe i didn't think about that" ideas thats cheap as a blowjob. CRD and some other shops incidentally have been running them on thier cars for a while.

Edited by GeeTR

GReddy also make an Oil Filter that has a magnet built in. I have been using these for quite a while, however as far as I'm aware they are being discontinued so this might be the next step for me.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, the trouble with that ^^ is: The configuration shown is absolutely a 1-way, not a 1.5-way. There is no way that a 1.5-way can be said to offer LSD action only on acceleration. If Nismo cannot get that right, then it is impossible to believe their documentation. That ^ is not a 1.5 way setup. That is a 1-way.   And so now I have allowed all doubts to flourish and have gone back to look at the MotoIQ video. I originally made the mistake of believing him when he said "this is a 1.5-way" at the ~6:10 mark. Because what he did was take the gear assembly out of the 2-way opening and just rotate it one place to the left to drop it into the 1-way opening. When he dropped it in there, the cam was "backwards" compared to the correct orientation shown in all other photos of that config. The flat shold have been facing the 1° ramp side of the opening, not the 55° ramp side. And I thought, "gee that's cute", but I was concerned at the time, when he put the other ring back on, that the gap between the rings looked like it was wider then in the 2-way config. And then I said a lot of things in my long post on Tuesday that could only make sense if the guy from MotoIQ was correct about what he'd done. BUT... I have now done my homework. I grabbed a frame of the video with the 2-way config, and then grabbed another with the "1.5-way" config, snipped out the cam and opening of that frame and just pasted it direct on top of the 2-way config. I scaled it so that the triangular opening was almost exactly the same height in both. AND.... the gap between the plates is wider with the cam installed in the triangualr opening backwards. That is.... it cannot go together that way. There would be massive force on the plates all the time, if you could even reassemble it.  So, My statement on the matter? The Nismo diff is actually only a 2-way and 1-way. There is no 1.5-way option in it, regardless of what they say. Here's a photo of a real 1.5-way ramp opening from Cusco (along with the 1 way option). And the full set of 1 through 2 way options from their racing diff, which is not same-same as what we'd typically be using, but...the cams work the same. A little blurry, but it comes from this Cusco doc, which is quite helpful. AND.... Cusco do in fact do what I suggested would be sensible, which is to have rings that do 1 and 1.5, and 1.5 and 2. Separately.  
    • Welcome Adam. Car looks great!
    • "With a 1.5-WAY, the LSD is effective only during acceleration."
    • Well it wasn't as easy as I thought.... and it also wasn't in my original manual which I did end up finding. They discuss the process in the Nismo catalogue though and it requires slight machining. Page 145.  NISMO PARTS CATALOGUE 2020
    • I'm an idiot, my intercooler is rated for 1000hp. I had clicked on the wrong product. Knowing the delta P would be nice, but I'm doubtful I'll do it. Now as for an EMAP, that would be great and I'll get around to it eventually but from my findings in my last post, I'm considering a turbo swap now. 
×
×
  • Create New...