Jump to content
SAU Community

Recommended Posts

geez roo lets keep it clean!! lol...

I'm talking about the exhausts. Where's your mind at :blink:

Hey babe, I got Simo coming over tonight. Tattoo appointment has been moved to Monday night! What you guys doing tonight? If you're not doing the dinner, come over! :banana:

Spotted Nene's new 260 last night. But just like Flick, her man was driving it :banana: Kick him outta the driver's seat Nene! :blink:

haha i had a good laugh at this comment ruby :P

Im just lazy.. even in the NX, i always ask luke if he wants to drive.. i get too much road rage anyway :S

While im in this thread

White 33 four door on tapleys hill road this arvo just near harbour town, and a dirty muddy burgandy 32.

Spotted a silver 32 GTR going north down south road just before anzac h/w last night around 5.45pm. Very nice.

Also a blue 33 going south same place, just after the 32, was very dirty, 2 guys in it.

And then a midnight blue or black R33 GTR on bains road i think it was waiting at the lights at south road. Had what looked to be standard GTR rims, looked clean, i was on the bus with the wicked blue lights LOL if you saw it. :)

Spotted DSTROY last night at west lakes carpark at 9 pm, was in my maroon 33

We were on our way to the ramsgate too in the mood to go out instead of a cruise

f**ken love your car!

hey spotted a white 33 on south rd tonight at 5:15pm aprox, thanx for letting me in the traffic us skyline owners need to look after each other :rolleyes:

yeah i always lets stags and lines in :)

spotted a nice white stag yesterday @ ridgehaven shops on north east rd

saw chad turning off west tce onto waymouth street tonite at about 7:45pm, i was in the rad white daewoo.

also saw a maroon 32 gtr vspec with VSPEC plates in the carpark of HJ's on anzacs shortly after. i went up n said hello to the guy who owned it, he was tripping that i picked him out of all the ppl in HJ's till i pointed out that he had a nissan lanyard hanging out of his pocket :rolleyes: nice guy, but not on SAU

Was with my friends last night (kahli in R32 and Mike stock black R34). Saw a R31 RS, black with grey bottom and black Drift Teks, got stuck in the car wash at BP Brighton, also with a red one. Then some dark Green Commodore shot a red light going waaaaaaaay too fast and almost took us out. Kahli followed it and called the cops.

spotted a black R34 out the front of my house @ 7am 5 people in the car dropping one or two off from a night on the town

sounded nice he drove around the corner then 50m down the road hit the clutch and hit the limiter then carried on :D nothing silly just hit the limiter

then on the main road heard him up to the round about near me again nothing silly just driving with an exhaust :bunny: gave me some idea how far away you can hear my car, did sound very nice, dunno Tom was he your mate or i thought Kraftw3rk

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...