Jump to content
SAU Community

Recommended Posts

Spotted someone not paying attention and running into the back of another car at the intersection about to turn right... that doesn't bother me they can sort it out.... BUT GET THE HELL OUT OF THE WAY! IT WAS BARELY A LOVE NUDGE AND YOUS ARE STOPPED AT THE FRONT OF THE SLIP LANE PREVENTING EVERYONE ELSE FROM MOVING ALONG! MOVE YOUR CAR FFS AND DEAL WITH IT ON THE SIDE OF THE ROAD! /end rant

  • Like 2

Spotted a neat R32 GTR having some fun with me on my way to work this morning in the RX7.

Its days like these I sincerely miss the awd of my Stagea. Even driving 100% sensibly I have trouble getting traction!

spotted a red VN sliding into and ONTO a gutter at munno parra shops. lucky no pedestrians were around. you f*ckhead.

I had the same red VN but on port river exspress way drove up to me and started honking and putting there middle finger up at me. it was a car loads of junkies. hope they crash

spotted a S2 33 4 door some time ago now in my hood :D:wave:

i also spotted this yesterday

Something about rain and Adelaide drivers... Dr jeckyll mr Hyde. Might have to start a towtruck business :)

standard for a lowered commo.

spotted james' 'R on north east road at about 9:30, never thought id say this... but put the works back on. gtc's dont really suit.

then spotted W4NTED chucking a lap on hindley at midnight.

then james again on the way home. quite amusing. :action-smiley-069:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...