Jump to content
SAU Community

Recommended Posts

Spotted kahli near thebby theatre today and I think Cosi came past my street around 4pm. Also while at autobahn mile end this arvo I heard a really nice rb clearing it's throat, it was a silver stag turning onto sir Donald bradman. Sounded good.

Yep crusiing in my hood :P

Spotted Deepdish v35 on beach front down Glenelg/somerton ..seen ya coming a mile away Nath :thumbsup: car gleaming clean as always

:cheers:

Silver r33 driving down seacombe rd round 2.. Flashed lights n waved but look liked u miss it! :action-smiley-069: lmao !

Bayside blue 34GTR anz highway round 345 heading towards beach ! In mates car getting into a fight about a worked 34 GTR v-spec would not beat a stock 911 of the same year :domokun:

Think Plates where Hostel ,hostal?? Was turning corner but god damn f**king sic and so clean! :thumbsup:

Silver r33 Brighton rd heading south bout 4:30.. nice exhaust .. Looking like he way enjoying the traffic as much as I was lol

Bayside blue 34GTR anz highway round 345 heading towards beach ! In mates car getting into a fight about a worked 34 GTR v-spec would not beat a stock 911 of the same year :domokun:

Think Plates where Hostel ,hostal?? Was turning corner but god damn f**king sic and so clean! :thumbsup:

Yep was me...plate HOSTILE, out and about on a nice arvo cruise for my day-off. :thumbsup:

weds night 9pm ish... black 32gtr red seats red rim wheels pulling onto sth rd near melrose pk kfc

thurs 3pm ish.... silver 32gtr at sturt and brighton intersection

4.30ish... black 34 coupe letting me in to pass a bus at hallet cove :thumbsup:

Spotted r33 in Murray bridge with the plates "copsb 8". Ur game driving around with those plates especially in bridge.

He's one of my neices friends, soon to be b/f i think, lives around Tailem Bend, also owns a black 33 set up for drift, guessing the one you saw was his grey one. Only 17 so you can understand the plates, although mine arnt much better haha

Spotted a dark coloured 32 last night pull out onto Port Road then duck down a side street on the left, followed you and went past as you were putting it in your garage.. Looked decent from what i saw... Round 6.30pm.

Spotted silver R33 seacombe road 435.. Flashed lights and thumbs up! :thumbsup:

Looked neat as !!!

Anyone going for cruz this weekend?

Thinking of Heading into hills with few mates including wrx wagon lol then pub lunch game of pool.. 280rwkw sil got defected so he is out and jumping in for passenger .. Few bikes comming gxr 1000 might make it half way after Wk.

Enjoy

He's one of my neices friends, soon to be b/f i think, lives around Tailem Bend, also owns a black 33 set up for drift, guessing the one you saw was his grey one. Only 17 so you can understand the plates, although mine arnt much better haha

Spotted a dark coloured 32 last night pull out onto Port Road then duck down a side street on the left, followed you and went past as you were putting it in your garage.. Looked decent from what i saw... Round 6.30pm.

Yeah it was the silver one-looked like he was only 17-18. I had a chuckle-my brothers car went thru a couple hours earlier to get off defect and then I saw the plates and thought "he's asking for one" sounded healthy tho! Spotted about 4 33s in bridge over the last few days--pt Augusta and bridge are meant to be he highest car theft towns in sa so id be keeping a very close eye on them If I was the owner.

yeah murray bridge is bad for defects, especially asking for one if driving 'spiritedly' in the built up areas.

i was there on thursday and counted 4 cop cars between the top of adelaide road and the bridge

i generally see a few when im up there.

im in murray bridge generally a couple of times a week for work.

delivering stuff in the truck to various places.

great drive with this gorgeous weather

Edited by sneaky1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...