Jump to content
SAU Community

Recommended Posts

As per the title, long story short, i cut the cable that runs from the cabin to the bonnet latch.

Quick question, does this make the bonnet more susceptible to flying open at high speeds and smashing my windscreen??

"oh sorry officer, the bonnet doesn't seem to be opening!.... i guess you can't inspect my engine bay :)"

*** slaps a defect sticker on window for not being able to open bonnet ***

*** slaps a defect sticker on window for not being able to open bonnet ***

actually it worked for me.. i broke the plastic on the latch and it couldnd be opened unless u had pleirs( pain in the arse though)

it was a big defect staton set up at the airport.. i got off without them even checking my hight or exhaust noise, both illegal :(

my 2 mates got fines

so has the original thread poster come back in here and tell us WHY he cut the cable?

He just felt bored. hahaha :O

I would assume that he cut it because he thought it was a cable tie or some speaker wiring. I've seen someone cut an important cable because they thought it was a cable tie. :(

jeebus, forgot about this thread!!

ok, story...

left keys in ignition... drains battery (not sure how, no lights were on) but not completely. Alarm remote still functions, car is arming and disarming (according to the icon on the remote) but not enough power to actually open the door locks.

Ring RACV. They come out, try initially to wedge the window open a bit where the it meets the soft rubber strip, so as to get a wire in to pull open door luck. Not much give in the window, RACV guy concerned window will shatter.

Puts wedge in between window and door rubber strip (horizontal bit) to try and get the door lock rod (horizontal). Manages to get the rod and door lock starts to come open. BUT even though there wasn't enough power to open the central locking, there was apparently enough power to KEEP the solenoid working and not allow the RACV guy to actually open the lock. Highly annoying.

Keeps trying for 30mins+, different wires etc... I then say, if we can get to the battery, perhaps if we jump it, it will solve our central locking problem. So i try pulling on the bonnet cable by reaching from underneath the front bumper. Get the latch to move about 1mm, but Nissan have thought of this, and the wire that does the opening is on the inside of a plastic covering so pulling on it does jack shit.

I then ask, can we cut the bonnet cable? Discussion ensued about relative pro's and con's and prices of getting locksmiths out. Decide to cut the bonnet wire.

EASIER F*CKING SAID THAN DONE!!! It is one tough mofo of a wire to cut, especially when i have a street sweeper spec front bumper, it was hard to get to and then it took both our efforts to cut the f*cker (the wire that actually does anything is encased in strands of steel cable!!) Eventually cut our way through and the latch pops open!! yipee!!

Pop bonnet, jump battery, alarm starts working again, opens the central locking and away i go.

$60 for bonnet cable from Nisswreck in SA, but has yet to be installed. Anyone know if it will be a shitter of a job?

/end story

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
    • Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
×
×
  • Create New...