Jump to content
SAU Community

Will Slotted Dba Rotors That Were On A 33 Fit My 32gtr?

02_FNE
 Share

Recommended Posts

Duncan Grand Master

Duncan

Posted
Posted

what was wrong with my last answer lol btw dba4000 are kangaroo paw, dba5000 have normal cooling vanes (and are 2 peice). either are fine unless you do a lot of track work (dba4000 have been known to crack, check back through the last few months in this section)

02_FNE Community Regular

02_FNE

Posted
  • Author
Posted (edited)
The 5000s with normal cooling vanes are meant to be limtied offer or something. Even if they turn out to be a normal stock.shelf rotor i think you will find the 5000s are Kangaroo Paw as well

ok, thats good, so they are def worth puttin on..

whats the difference between them ^^ kangaroo paws?

oh and yeh im only using them for street use.. just a heavy footed street driver..

Edited by 02_FNE
SLY33 Mentor

SLY33

Posted
Posted (edited)
what was wrong with my last answer lol btw dba4000 are kangaroo paw, dba5000 have normal cooling vanes (and are 2 peice). either are fine unless you do a lot of track work (dba4000 have been known to crack, check back through the last few months in this section)

Lol, yes i thought your first answer was sufficient :D

my dba4000's cracked, using with Re55 semi's, and with street use only! Dont know the story or if theyve changed anything, but ive since gone OEM rotors, had them slotted and cryo treated and so far have been a treat. Cryo treating seems to be the key!!

Edited by SLY33

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      V37 Suspension change

      By Duncan · Posted

      You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      OK, so a bunch of trim needs to come off to get to the rear shock top mounts. Once the seat is out of the way, the plastic trim needs to come off. Remove 2 clips at the top then slide the trim towards the centre of the car to clear the lower clip Next you need to be able to lift the parcel shelf, which means you need to remove the mid dark trim around the door, and then the upper light trim above the parcel shelf. The mid trim has a clip in the middle to remove first, then lift the lowest trim off the top of the mid trim (unclips). At the top there is a hidden clip on the inner side to release first by pulling inwards, then the main clip releases by pulling the top towards the front of the car. The door seal comes off with the trim, just put them aside. The the lighter upper trim, this is easy to break to top clips so take it carefully. There is a hidden clip towards the bottom and another in the middle to release first by pulling inwards. Once they are out, there are 3 clips along the rear windscreen side of the panel that are hard to get under. This is what the rear of the panel looks like to assist:
    • GTSBoy
      R34 manual conversion speed signal wire finding, need help

      By GTSBoy · Posted

      Yes. Autos typically work from the speed sensor on the pinion shaft of the diff. I also think that even if you have a proper speed sensor for the bog manual in the manual box, that the signal it outputs is not compatible with the auto dash anyway. You should consult that manual (the book, not the gearbox).
    • GTSBoy
      First time Skyline owner

      By GTSBoy · Posted

      And I just realised that that advice is slightly nonsensical for a GTR, because you need 2 of them. But it is otherwise true.
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Having had a reasonable look at the car, I'll be able to remove the (one time) rams and retract the hinge (they are held in the down location by a tiny (m3?) sacrificial screw) which will get it physically back in shape. From there if you remove the rams you need a resistor to turn off the airbag light (as Mark said, there are plug in kits and I might go that way because its reversible). And...per all the threads on here, even if you have the resistors to turn off the airbag light, the bonnet light will stay on as it writes to the airbag computer history - that is either replace the airbag controller, reprogam the EPROM (if I can work out how), or remove the globe from the dash. Having seen how sensitive this system is, if I had my time over I'd pre-emptively remove the rams, even on a road car, because this is all a very unnecessary pain in the arse. Reminds me, time to go and have a look at the Fuga too....
×
×
  • Create New...