Jump to content
SAU Community

Recommended Posts

well it might be actually possible, would need subframe off, sump off, crank out, balancer off, timing gear off, timing belt off, oil pump off, gearbox off, clutch off and flywheel off.

but if you did all that you could probably get to all of the bearings.

seriously though, if you need new big end bearings, rebuild the motor. the main bearings are probably in trouble, there is most likely some crap floating around somewhere, might as well do a hone and new rings while you are in there. pull it apart, clean and check it all, put it back together. so much damn work just to get the sump off

You wouldn't have to remove your crank to change B/E brgs. I've changed them on various other motors in the past by removing the B/E caps & spark plugs, pushing each piston up an inch and being real careful not to nick the journals with the thread on the B/E bolts, if you do, crank has to come out (might have to come out anyway for a grind or at least a linish if its got grooves).

You'll have to do a r & r on each cyl that's on the down stroke then turn crank to do others.....pretty messy this way but good oportunity to replace with a decent baffled sump.

As far as mains are concerned, they rarely fail unless there's crap in the galleries but usually evident by pitting or scratches on the B/E shells.

You CANNOT get the sump off with the gear box attached, there are two bolts behind the flywheel. This has been covered before, It is not practical to take the box out, to remove the sump. Just pull the engine, there is no way around it. And yes, I have done it.

Sorry to be a spoil sport

ok thats fine.... just wanted to find out first as i have never worked on a rb26 befor motor has only been rebuilt not long ago.... it got low on oil and now has the knock at around 3 4000 ill get some one to do all the work and check every thing

might be time for the bigger turbos at the same time :domokun:

You wouldn't have to remove your crank to change B/E brgs. I've changed them on various other motors in the past
You CANNOT get the sump off with the gear box attached, there are two bolts behind the flywheel. This has been covered before, It is not practical to take the box out, to remove the sump. Just pull the engine, there is no way around it. And yes, I have done it.

Sorry to be a spoil sport

Fair enough, its good info to know. As I stated above, I have removed sumps on various other motors whilst still in the car but not on an RB, thanks.

yes so have i thats why i asked.....it has cp pistions and a baffled sump ect all ready and light weight rods im not sure what type of bearings were used tho any ideas on how to tell?

Check numbers on the back of the shell, may give a clue, or if your not using them again light scrape on inside will tell you if they're copper leads or alu tins. Always a good idea to use a copper lead or similar in an RB though.

Huh??? Same thing....you gotta remove the B/E cap to remove the B/E brg. What sort of other B/E is there?
Where do you think the big end bearing sits, and what does it protect? The Big End (it's the end of the conrod that connects to the crankshaft).

If you are referring to the big end bearing, then call it that.

Where do you think the big end bearing sits, and what does it protect? The Big End (it's the end of the conrod that connects to the crankshaft).

If you are referring to the big end bearing, then call it that.

Been in the engine reconditioning game for 20 years mate so I appreciate you teaching me something that I learnt when I was still in nappies.

When engine reconditioners say they're changing their B/E's, they're always referring to shells. Otherwise they refer to the rods specifically. They never talk about changing B/E whilst referring to rods.

Sounds like you like to make a play on peoples words and argue pointless issues otherwise you wouldn't have asked such an obvious question.

Been in the engine reconditioning game for 20 years mate so I appreciate you teaching me something that I learnt when I was still in nappies.

When engine reconditioners say they're changing their B/E's, they're always referring to shells. Otherwise they refer to the rods specifically. They never talk about changing B/E whilst referring to rods.

Sounds like you like to make a play on peoples words and argue pointless issues otherwise you wouldn't have asked such an obvious question.

Sorry, didn't realise you had so much experience in these matters.

Yes, I can be a pedantic old bastard sometimes. It's just that there are quite a few younger members who don't always understand the technicalities.

And the only stupid question is the one you don't ask.

Sorry, didn't realise you had so much experience in these matters.

Yes, I can be a pedantic old bastard sometimes. It's just that there are quite a few younger members who don't always understand the technicalities.

And the only stupid question is the one you don't ask.

Yeah no probs bud, I know what you mean & I agree, its like banging your head on the wall sometimes. :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There are black hose clamps as well if you care. Plazmaman for example sells some: https://plazmaman.com/product/black-hose-clamps-premium-quality-stainless-breeze/
    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
×
×
  • Create New...