Jump to content
SAU Community

Recommended Posts

not too sure man, u gotta ask Matt (Femno on these forums, he works there)..i havent tuned there but did do a run for about 60 bucks a while back

I'm letting matt tune my car since he built it all. I'm sure he will do a good job. Will let you know how he does

haha thanks :( bit of a Bleach fan... can u tell ????? :laugh:

i'm thinking about putting a Bleach sticker on the STAG

Me too :banana: although I think a big bleach sticker in-lieu of a work shop sticker or nothing at all would look quite ricey! :3some:

Spotted WANZI earlier tonight on the Monash, came on from Stud Rd I think... I was the little white Excel in front of you going through Narre Warren until you took the Narre Warren exit :P

Was heading to krispy Kreme I go there every tues night wit mates

Was overtaken by a black r33 gtr on the Wellington Ed exit off the monash tonight. Then along springvale road spotted an sau sticker on a silver r34 heading down springvale road. Also saw a white r32 gtr, black r32 gtst and a grey r32 gts while at krispy kreme tonight

spotted an R32 GTST last ight around 8pm on edgars. had SAU stickers

then an R32 GTR, white at about 8:23

then an R32 GTR? had a badge and wider guards, as well as a rear diffuser. but a bomex front bar? around 8:30, same spot

I'm letting matt tune my car since he built it all. I'm sure he will do a good job. Will let you know how he does

cool, he knows his stuff, look forward to see how much u make,,if ur car's still there on monday then i guess i'll b spotting it again lol,,takin the car back to get a couple more things done

Spotted unmarked cop car at my mate's work getting some work done on it

I do have more pics

post-20278-1260415511_thumb.jpg

:D

also spotted a white r33 GTR with white wheels on warrandyte rd ringwood just near the Quix Mobil at about 2.45ish

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
×
×
  • Create New...