Jump to content
SAU Community

Recommended Posts

You folks are too bias. The Z06 was faster.

The Z06 did 0-100 in 8.5 seconds and the GTR did it in 8.9.

The GTR did better 0-100-0, but they had a better reaction time in the GTR (time between WOT and hitting brake pedal).

GT-R: 0-100 = 8.9, 100-0 = 4.3, accel to brake reaction time = 0.6

Z06: 0-100 = 8.5, 100-0 = 4.5, accel to brake reaction time = 1.0

Thus, if you subtract the difference in reaction times, the Z06 was not only faster 0-100, but it's faster 0-100-0 also!

The Z06's lead would've been even larger had they kept going (the article mentioned that the Z06 was accelerating harder past 100mph....this also hurt its braking time).

The Z06 is even more impressive because it has inferior tires and hit the market a full THREE years before the GTR.

0-100-0 implies that you'll start timing from the moment the car accelerates up to 100mph and finish timing once it reaches a complete stop. Thats not very complicated, is it? Last time I checked 13.9 < 14.0 :thumbsup:

Seriously though, can't you just appreciate that they are both great cars and are fast enough?

  • Replies 41
  • Created
  • Last Reply

Top Posters In This Topic

0-100-0 implies that you'll start timing from the moment the car accelerates up to 100mph and finish timing once it reaches a complete stop.
Comments like these usually mean the GTR accelerated faster:
yep gtr outsprints the Z06!
Did I hear him say that it outran the Z06 ??

I didn't know a sprint and "outrunning" included stopping....

Regardless, their reaction time in the Z06 explains why the GTR was a tenth quicker 0-100-0. The reaction time was 0.4 slower in the Z06, thus given an equal reaction time the Z06's time would've been 0.3 better. Getting the same same reaction time is unlikely - kinda like getting the same reaction time in the 1/4-mile on back-to-back runs. The human factor just happened to favor the GTR. You can claim that as a victory, but it is definitely a hollow one.

Additionally, they said the Z06 was accelerating past 100mph faster (more momentum). Also, the driver had just had to change to 3rd to get to 100 which meant it was more difficult to judge when to brake.

Edited by edwardhaskell
Comments like these usually mean the GTR accelerated faster:

I didn't know a sprint and "outrunning" included stopping....

Regardless, their reaction time in the Z06 explains why the GTR was a tenth quicker 0-100-0. The reaction time was 0.4 slower in the Z06, thus given an equal reaction time the Z06's time would've been 0.3 better. Getting the same same reaction time is unlikely - kinda like getting the same reaction time in the 1/4-mile on back-to-back runs. The human factor just happened to favor the GTR. You can claim that as a victory, but it is definitely a hollow one.

Additionally, they said the Z06 was accelerating past 100mph faster (more momentum). Also, the driver had just had to change to 3rd to get to 100 which meant it was more difficult to judge when to brake.

You know what, they're just cars. If you can't figure out that many people on this forum are CAR enthusiasts and can appreciate many types of performance cars (including the Z06) then you need to read threads other than this one.

yes it annihilated the opposition, it took them 3 cars and still couldn't touch the GTR.

drag race was a little dodgy though, I think I'd like to see an acutal 1/4 mile with the computer shot in the head.

You folks are too bias. The Z06 was faster.

The Z06 did 0-100 in 8.5 seconds and the GTR did it in 8.9.

The GTR did better 0-100-0, but they had a better reaction time in the GTR (time between WOT and hitting brake pedal).

GT-R: 0-100 = 8.9, 100-0 = 4.3, accel to brake reaction time = 0.6

Z06: 0-100 = 8.5, 100-0 = 4.5, accel to brake reaction time = 1.0

Thus, if you subtract the difference in reaction times, the Z06 was not only faster 0-100, but it's faster 0-100-0 also!

The Z06's lead would've been even larger had they kept going (the article mentioned that the Z06 was accelerating harder past 100mph....this also hurt its braking time).

The Z06 is even more impressive because it has inferior tires and hit the market a full THREE years before the GTR.

You guys know good old Ed here is from the corvette forum, just coming over here to justify why they lost with some lame number crunching BS. Hey Ed, go back to your pushrod V8 farm plow loving. Yeeehaw

The ZR1 corvette will probably top the R35

Agreed. The V spec will be more of a competition for the ZR-1.

The Z06 is an aweosme piece of machinery which did hit the mark a few years before the R35 did. In saying that the GTR is slightly slower at the high end of the scale but at those speeds who really cares :D

Edited by Zoggy
You guys know good old Ed here is from the corvette forum, just coming over here to justify why they lost with some lame number crunching BS. Hey Ed, go back to your pushrod V8 farm plow loving. Yeeehaw

hahhahahaaha

i lol'd :)

last time i checked, the Z06 and the GTR both had steering wheels....

i'm pretty sure cars are meant to turn aren't they? although judging from some of these linked threads and comments in here, i'm not sure everyone understands that.. i must admit, it's hard to get your head around...

>_<

You folks are too bias. The Z06 was faster.

The Z06 did 0-100 in 8.5 seconds and the GTR did it in 8.9.

The GTR did better 0-100-0, but they had a better reaction time in the GTR (time between WOT and hitting brake pedal).

GT-R: 0-100 = 8.9, 100-0 = 4.3, accel to brake reaction time = 0.6

Z06: 0-100 = 8.5, 100-0 = 4.5, accel to brake reaction time = 1.0

Thus, if you subtract the difference in reaction times, the Z06 was not only faster 0-100, but it's faster 0-100-0 also!

The Z06's lead would've been even larger had they kept going (the article mentioned that the Z06 was accelerating harder past 100mph....this also hurt its braking time).

The Z06 is even more impressive because it has inferior tires and hit the market a full THREE years before the GTR.

The Z06 is a faster top end car. Power to weight ...easy math. There are fair whack of other cars faster than the Z06 and GTR again in this area.

However getting the pig off the line or round a corner fast without really having to get it perfect makes the car nice too don't you think?

Nice to buy a car with good traction and handling out of the box, we all like that. The factory don't hand the Z06 to you like that at present (as good as it could be). They do give you the GTR that way. Always sucks when the factory skimp on tyres etc. but, then thats what stock means.

There have been plenty of reviews now on various great cars compared to the new R35 from all over the world. There is now a very basic agreement that it's the best bit of kit you can buy for the price replacing the very worthy Z06 for 'bang for buck'.

Z06 is a great performer but, it's out gunned by the GTR in all but, outright straight line speed. Even then the gap is still very narrow. But, straight line speed isn't worth much in the equation I've owned a few cars that make the GTR and Z06 look like nerd toys for straight line speed. The same cars however would be in the dust behind the Z06 trying to go around a corner or stop.

Admit the GTR is great and if your not going to buy a Z06 a pretty good second option or visa versa.

last time i checked, the Z06 and the GTR both had steering wheels....

i'm pretty sure cars are meant to turn aren't they? although judging from some of these linked threads and comments in here, i'm not sure everyone understands that.. i must admit, it's hard to get your head around...

:rofl:

The point of the evo article was to race the best accelerating car (Corvette) in a straight line, the best road car (the Audi R8) on the road and the most track based weapon (the GT3) on the track to see how the GTR stacks up against the best of everything. It did a damn good job.

When I say the "best" I mean Evo's version of the best when you exclude straight out super cars.

I was actually most surprised to hear that it was faster than the Audi on bumpy Welsh roads and that the driver of the GTR needed to feather the throttle on the straight to allow the Audi to keep up, so that he could see how hard the driver was pushing to keep up.

It will be interesting to see how fast the v-spec is. Just imagine if it lost even 200kg's and gained 50 horses.

Nissan have done an outstanding job, as the article says it is the new benchmark.

Cheers

Comments like these usually mean the GTR accelerated faster:

I didn't know a sprint and "outrunning" included stopping....

Regardless, their reaction time in the Z06 explains why the GTR was a tenth quicker 0-100-0. The reaction time was 0.4 slower in the Z06, thus given an equal reaction time the Z06's time would've been 0.3 better. Getting the same same reaction time is unlikely - kinda like getting the same reaction time in the 1/4-mile on back-to-back runs. The human factor just happened to favor the GTR. You can claim that as a victory, but it is definitely a hollow one.

Additionally, they said the Z06 was accelerating past 100mph faster (more momentum). Also, the driver had just had to change to 3rd to get to 100 which meant it was more difficult to judge when to brake.

This is the thing about yank cars, all you seem to care about is how fast you can make it go in a straight line....

Cars have steering for a reason. Its a wounder people dont just replace drag strips with rails and race trains?

This is the thing about yank cars, all you seem to care about is how fast you can make it go in a straight line....

Cars have steering for a reason. Its a wounder people dont just replace drag strips with rails and race trains?

I love how ppl write of the Corvette saying sit doesnt handle. Its Australian built brakes are about the best steel brakes you can get on a production car. They are brilliant and fade free. And the car handles very well. How else can a Z06 be only 4 seconds slower over a lap of a 20km track, all with no traction control or 4wd or other gayness?

The GTR is perhaps the best all round performance car getting around at the moment. Especially for the dollars. But why does that mean ppl cant give credit to cars that do similar things differently? Hell the Vette is as quick as a GT2 Porsche...so how can you be so stoooopid as to say they dont handle :rofl: But consider for a second the asking price of the Z06, cosnider its only rwd and doesnt have a gay automatic gearbox, instead 3 pedals and a real gearbox which i understand is a cavemans way of changing gears these days, and a slower way to hurl the car down the road....and tell me the Z06 isnt a blindingly fast car. Hell getting back to the 20km Ring example, how many gearchanges are there in that lap? There could be the 4 seconds there? So you cant say they dont handle!!!!

At the end of the day they are all quick enough for me...it comes down to styling and sound for me. So this

bluedevil.jpg

Versus this

20071024_gtrworld_051.jpg

And go watch the Top Gear adn 5th Gear vids of the Z06...the thing sounds great and is a hoot to drive.

I had a mate recently go to the US and rent out a z06... Just by going on what he said, it didnt handle to save itself. Prehaps he was wrong, I doubt it as he drove it around for a week, and when hes here he owns a 02ish commodore, but feh.

There yank tanks that will never be availible here. I dont really get why we dont import more, I mean we import enough grey imports from japan right? But you never really see much in the way of yankee cars. Not that I mind, I dont really like them.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
×
×
  • Create New...