Jump to content
SAU Community

Recommended Posts

I've got a problem with my friend's 180SX.

After it is warm it only takes 3-4 full throttle runs to redline to get his water temp up to the 90s, and it takes ages to come back down. He used to drift it at Winton with no issues until one day when it just overheated on the track and has been doing it ever since.

Since that day, to try and fix it we have:

- Rebuilt head. Cleaned up the whole thing, port and polished the ports and installed new head gasket.

- Removed thermostat.

- Installed Alloy Radiator

- Installed Twin Thermos

- Bypassed heater core

- Changed Water Pump

- Flushed the whole system

And it still does it! Can anyone think of anything we've missed? One of our friends suggested that the water pump could be sucking the radiator hose closed at high rpm, but I've never heard of that happening before?

Car is running a T518Z, is an SR and is making around 240rwkw if it makes any difference.

Thanks,

Peter

Edited by Equinox
Link to comment
https://www.sau.com.au/forums/topic/213318-overheating-180sx/
Share on other sites

not to sure about your engine, but on the Rb26 if you remove the thermostat entirely then the water will bypass the block and just go straight out the outlet pipe as its only 100 mm apart. As most things it will take the path of least resistance and the rb26 has a 25 mm hole in the back of the themostat house which is connected the outlet pipe on the head.

Here is a writeup I did for NICO Club (US), maybe something in it will help.

OMG my RB is overheating

Oh, and the water pump sucking the line closed, that was my problem I believe. When I replaced the lower hose, which was soft with an OEM unit from tweakit, the overheating problem I had at constant higher RPM (Freeway) went away.

Edited by cpt_impossible

I'm pretty sure that an oil cooler will go a long way to fixing your heating problems. The thrust turbo's heat the oil up quite a bit as they are oil cooled and they run hotter than the equivalent water cooled BB turbos.

Do you have a SR with the factory heat exchanger on top of the oil filter or not? (some did some didn't) Even if it does they don't work very well.

I was having the same heating problems with my CA18 as i was getting oil temps around the 105 mark and water temps around 95 in general driving. As soon as i fitted an oil cooler i didn't get engine temps above the factory 82 degree's and the oil temps haven't been above 90 degrees

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...