Jump to content
SAU Community

Recommended Posts

Hi all

friends i have bad problem naw my rb25det build boost in nutral gear with stoped car

i heard that RICH & RETARD so i changed AIRflow METER 4 times and the mechanic changed the cas

3 times but still same thing can you help me pleas my car stoped i can`t drive it :)

Link to comment
https://www.sau.com.au/forums/topic/216461-rr-problem-without-solution/
Share on other sites

Hi all

friends i have bad problem naw my rb25det build boost in nutral gear with stoped car

i heard that RICH & RETARD so i changed AIRflow METER 4 times and the mechanic changed the cas

3 times but still same thing can you help me pleas my car stoped i can`t drive it :)

its also hisitating when driving

Hi dears

i did all this staff till now and about diagnostics i dont have tool

i changed maf 4 times all same result

i changed cas 3 times all same result

i tryed it without intercooler like direct its littel bit ok but small stuk from 5.5k to 6.5k rpm

and today we will try another turbocharger because some garage said if its littil crap will do same problem

so guys if some one have same this damin problem give us some help :thumbsup:

finally i am thinking that could be ignetion coils !!!!! :(

what mods are u running?

crook w/g actuator?

have u done a diagnostic? try resetting the ecu properly(shorting the 2 pins in the plug method)

dear am using stock turbo with stock wastegate but before i changed it i hade rb20det w/g

to gaine 10 psi

this thing start when i put new greedy front intercooler

I think your timing is off, is it being correctly adjusted AFTER you've been changing over the CAS sensors?

There isnt many things that will cause boost buildup in neutral and timing is the big one

Or the gauge could be faulty, put a decent one on there or are you using the stocker? (dont trust the stock one)

UltimateGTR - nothing to do with actutors etc... its not under load in idle plus the gate is closed on idle normally anyhow, so its gotta be fuel related, ie before turbo

I think your timing is off, is it being correctly adjusted AFTER you've been changing over the CAS sensors?

There isnt many things that will cause boost buildup in neutral and timing is the big one

Or the gauge could be faulty, put a decent one on there or are you using the stocker? (dont trust the stock one)

UltimateGTR - nothing to do with actutors etc... its not under load in idle plus the gate is closed on idle normally anyhow, so its gotta be fuel related, ie before turbo

no man when we changed the cas we adjust the timing by timing light

even i changed ecu with good one also i changed the coils all do same problem

but when we retaind factory intake manifold problem hapen in 5.5 to 6k

but really how could boost come up like antilage in nutral :banana:

i belive its ignition but where i don`t know

  • 2 weeks later...
When the timing is set, is the cas near the centre? Your harmonic balancer may have slipped, and your setting the timing very retarded.

yes brother its in center and with timing gun i got like 12 - 13 degres

all my mods now 3 inch exhust and pod filter with greddy intercooler front mont

and gtr fuel pump also i changed the plugs

yestarday we changed the three wires all long from MAF to ecu and the car runs good

but still i have loosing power in 3rd 4rth gear :P

by the way i am going to buy power fc ecu do you agrre with me ? that it will help me too much

and thanks all for help

What you mean the problem happened @ 5500rpm/6000rpm with the factory plenum?

What other parts are changed?

Full listing please

its noticable loss of power that somthing hold your car moments

and my mods are 3 exhust pod filter intercooler gtr fuel pump thats all now

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
    • I saw your intro update, are you sure you've actually had a starter motor failure? You mention it could be the alarm causing it. I'm assuming you've got a no start issue, but what are the exact symptoms, as there could be a few reasons it has stopped wanting to start.
×
×
  • Create New...