Jump to content
SAU Community

Recommended Posts

Hi all

friends i have bad problem naw my rb25det build boost in nutral gear with stoped car

i heard that RICH & RETARD so i changed AIRflow METER 4 times and the mechanic changed the cas

3 times but still same thing can you help me pleas my car stoped i can`t drive it :)

Link to comment
https://www.sau.com.au/forums/topic/216461-rr-problem-without-solution/
Share on other sites

Hi all

friends i have bad problem naw my rb25det build boost in nutral gear with stoped car

i heard that RICH & RETARD so i changed AIRflow METER 4 times and the mechanic changed the cas

3 times but still same thing can you help me pleas my car stoped i can`t drive it :)

its also hisitating when driving

Hi dears

i did all this staff till now and about diagnostics i dont have tool

i changed maf 4 times all same result

i changed cas 3 times all same result

i tryed it without intercooler like direct its littel bit ok but small stuk from 5.5k to 6.5k rpm

and today we will try another turbocharger because some garage said if its littil crap will do same problem

so guys if some one have same this damin problem give us some help :thumbsup:

finally i am thinking that could be ignetion coils !!!!! :(

what mods are u running?

crook w/g actuator?

have u done a diagnostic? try resetting the ecu properly(shorting the 2 pins in the plug method)

dear am using stock turbo with stock wastegate but before i changed it i hade rb20det w/g

to gaine 10 psi

this thing start when i put new greedy front intercooler

I think your timing is off, is it being correctly adjusted AFTER you've been changing over the CAS sensors?

There isnt many things that will cause boost buildup in neutral and timing is the big one

Or the gauge could be faulty, put a decent one on there or are you using the stocker? (dont trust the stock one)

UltimateGTR - nothing to do with actutors etc... its not under load in idle plus the gate is closed on idle normally anyhow, so its gotta be fuel related, ie before turbo

I think your timing is off, is it being correctly adjusted AFTER you've been changing over the CAS sensors?

There isnt many things that will cause boost buildup in neutral and timing is the big one

Or the gauge could be faulty, put a decent one on there or are you using the stocker? (dont trust the stock one)

UltimateGTR - nothing to do with actutors etc... its not under load in idle plus the gate is closed on idle normally anyhow, so its gotta be fuel related, ie before turbo

no man when we changed the cas we adjust the timing by timing light

even i changed ecu with good one also i changed the coils all do same problem

but when we retaind factory intake manifold problem hapen in 5.5 to 6k

but really how could boost come up like antilage in nutral :banana:

i belive its ignition but where i don`t know

  • 2 weeks later...
When the timing is set, is the cas near the centre? Your harmonic balancer may have slipped, and your setting the timing very retarded.

yes brother its in center and with timing gun i got like 12 - 13 degres

all my mods now 3 inch exhust and pod filter with greddy intercooler front mont

and gtr fuel pump also i changed the plugs

yestarday we changed the three wires all long from MAF to ecu and the car runs good

but still i have loosing power in 3rd 4rth gear :P

by the way i am going to buy power fc ecu do you agrre with me ? that it will help me too much

and thanks all for help

What you mean the problem happened @ 5500rpm/6000rpm with the factory plenum?

What other parts are changed?

Full listing please

its noticable loss of power that somthing hold your car moments

and my mods are 3 exhust pod filter intercooler gtr fuel pump thats all now

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hang on. Let me get this straight. The desire is to have coilovers, BC in particular, to be MORE comfortable on Sydney roads than stock suspension? Well, that's obviously not right. BCs have crude damping design at the very best, and typically hard spring rates. BC stands for Billy Cart. And then, the desire is to put in some shitty old worn out stockers, to get it blue slipped and then put the BCs back in? And then.....what? Not worry about getting pulled up by the Plod? Because you seem to have raised a worry about paying for engineering (which actually does solve all your legality problems) and still getting pulled up.... but the only problem there is that if/when that happens you have to show your paperwork at the inspection station. Whereas, if you just swap in borrowed shitty old stockers to get it slipped now, and then you get defected in the future, you have to go find more shitty old stockers then too. You course of action looks like this set of options: Buy brand new stock type dampers, and springs. probably cost a bit more than $1k all up, but will last for the remaining life of the car. Put them in, pass inspection, drive on them forever more. Hell, they could even be really nice Bilsteins and Kings or other lower&stiffer springs if you wanted. Get the car engineered as is. ~$1k. Buy new Shockworks coilvers (or MCA) and also pay for engineering. You're spending a lot more here. But these will be the best things that you could drive around on.
    • Might be worthwhile hitting up Facebook's groups, I know most of them contain terrible people and scammers - however you might be able to find someone that's in Sydney with factory suspension you could purchase and/or hire. Just do not send any form of money anywhere, in person cash only.
    • Thanks @Duncan Ride height is fine. I think it's almost stock tbh. Happy to share a pic. I don't actually have a regular mechanic as haven't lived in Sydney too long. Could you or anyone recommend any shops in Sydney?
    • You just need a different blue slip shop (preferably one you regularly use as a mechanic), and make sure the coil overs are as close as possible to standard height
    • yeah the sugar refining companies were pushing for the same in Oz originally, all fuels were going to have 10% ethanol to make them "cheaper" (noting, that the loss in l/100 might be greater than the decrease in price). I guess they won that fight in Canadia
×
×
  • Create New...