Jump to content
SAU Community

Recommended Posts

I believe the S1.5 has the S2 turbo in it. But as far as i'm aware it doesnt really matter if you have the nylon or ceramic they will both fall apart once boost is increased to 12 or more PSI.

Its kind of the luck of the draw. I'm personally running 12PSI on a 95 S1.5 (spikes out to 1 bar sometimes as im using a bleed valve not a boost controller as such) and have been for some months with no issues.

Link to comment
https://www.sau.com.au/forums/topic/217124-series-15-turbo/#findComment-3833407
Share on other sites

I ran a series 1 turbo @ 18psi for bout 18months on my old rb20. Never had a probably. when i pulled the turbo off it seemed happy lol. little bit of oil, minimal shaft play still and no weird bearing noises or anything. Probably luck though.

Link to comment
https://www.sau.com.au/forums/topic/217124-series-15-turbo/#findComment-3833515
Share on other sites

What makes you say that? Quite obviously there is... cause I own one. It has heaps of S2 features/parts that S1's never had.
I'm with you, there is an "in between model" I recently wrecked a S1.5 it wasnt a S2, it had S1 front end and other distinguishing features to the S1, S2 airbag wheel, S2 afm, and more, all origonal, anyways off topic Edited by madaz R33
Link to comment
https://www.sau.com.au/forums/topic/217124-series-15-turbo/#findComment-3833737
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That's probably OK. That's a face to face compression joint between two surfaces with the clamping load provided by those bolts. So.... it's unlikely that the bolts will end up feeling that load in shear, unless the clamping surfaces are not large enough, bolts not got enough tension on them, etc etc to prevent the two faces from moving wrt each other. Which... I would hope the designers have considered, seeing as it's probably one of the most important things the upright has to do apart from resist collapsing in its own right. But yes, it would definitely be worth asking them what their safety factor on that part of the design was. I tend to think that the casting, being a casting, is not necessarily the strongest bit of material in the world. It's about an inch square, and when you think about the loads that are being put into it, you have to wonder what safety factor the Nissan boys (and every other OEM engineer who has designed all the millions of other uprights that look essentially the same) used to account for defective casting, aging, severe impacts on the wheel, etc etc. 
    • Those bolts would be orders of magnitude stronger that cast aluminium though.  And its mainly clamping force, not shear they are dealing with?
    • Except all that twisting force that is breaking a cast piece, appears to be going through 4 bolts in the picture Johnny posted of the BryPar one...
    • The smart approach is to use the gearbox loom from the manual car. Makes it a lot easier - just plugs into the switches on the box and plugs into the main loom up near the fusebox. Then you only need to deal with bypassing the inhibit switch. The other approach requires you to use the wiring diagram to identify those wires by colour and location, perhaps even indulging in a little multimeter action to trace them end to end to make sure, and then.... you will have the answers you need. The R34 wiring diagram is available on-line (no, I do not have a link to it myself - I would have to do a search if I wasn't able to go to the copy I have at home).
    • Hi, i’m converted my r34 4dr auto to manual but need help with gearbox wiring. There are bunch of wires no idea which one for speedo drive, neutral, reverse can anyone help me. IMG_6860.mov
×
×
  • Create New...