Jump to content
SAU Community

Recommended Posts

Just had my exhaust completed by adding 3" dump and front pipes to the existing 3" hi-flow cat and 3" cat-back system.

Problem now is that the acceleration *feels* lazy, especially 2nd gear. Even the dodgy stock boost gauge is peaking a bit lower than what it was. Granted, I haven't got any actual data to show for a loss in power, but its a feeling that I'm getting which is enough for me. :D

Its not a flat-patch at a certain rev-range, it simply feels that the car is slower all the way through.

Anyone else had this sort of experience?

On the plus side, I can hear the turbo spooling up more now, which I like but that doesn't make up for when I'm getting smaller in someone else's rear-view mirror.

Link to comment
https://www.sau.com.au/forums/topic/217298-is-this-common/
Share on other sites

I don't have a boost controller so I can only assume I'm running stock boost. That being said, the stock gauge reckons its running at about 9psi (needle *was* right on that middle mark between 0 and +7, now its just under it).

I wondered if the ECU wasn't used to the breathing space but I haven't done anything about that (no piggybacker or reset or anything logical) and I'm pretty certain the O2 sensor is ok. It will be old, but ok and I'm basing that on the fact that the car was doing well before the new pipes were put it. Although, I'm now wondering if the mechanic perhaps had a go at cleaning the o2 sensor. Would that have an affect on the ECU at first, particularly if it was really grubby before?

Link to comment
https://www.sau.com.au/forums/topic/217298-is-this-common/#findComment-3836673
Share on other sites

I put FMIC, Pod, Full exhaust and my car went worse than before the mods. once I got my turbo Hiflowed and tuned to suit all the mods...Its a Rocket.

Stock ECU is good for the STOCK setup once you change something the tune needs to change with it. do all the mods you wanna do then get a ECU of somesort either stand alone or piggyback and get it tuned properly.

My car has gone from using 13.5 Litres per 100 to 8.8 Lph, not to mention bucket loads more power on the loud pedal.

and still makes full boost by 3000rpm.

Dave

Link to comment
https://www.sau.com.au/forums/topic/217298-is-this-common/#findComment-3836741
Share on other sites

I was hoping to get an ECU remap with Dr Drift once I got my boost controller and FMIC installed. Unfortunately I probably won't be able to get the FMIC put in for a while.

What would people recommend so far as an interim tuning goes? Is it worth it, or even possible (without any PFC/SAFC etc), to get some sort of tuning done prior to the FMIC?

Maybe I should resolve myself to biting either one of those bullets: "zero-power" or "empty-wallet" until a proper ECU solution is found.

Link to comment
https://www.sau.com.au/forums/topic/217298-is-this-common/#findComment-3836855
Share on other sites

If the computer is the problem why dont you just put the stock dump/front pipe back on then save for the computer then get it all done. Have you checked to make sure it was all installed properly? or did u tell your mechanic the situation?

Link to comment
https://www.sau.com.au/forums/topic/217298-is-this-common/#findComment-3837129
Share on other sites

Yeah as others have said.

I'd get it on a dyno.

Check the AFR's, fuel pressure, boost pressure and other basic things while there and get an idea of where the car it at.

Then workout what area it is thats needing the attention

Link to comment
https://www.sau.com.au/forums/topic/217298-is-this-common/#findComment-3838232
Share on other sites

  • 2 weeks later...

what? thats impossible, then why go for an extra dump pipe if you ain't going to tune your car?

What you guys are saying goes against the theory a turbo back gives more power than a cat back (with no tune).

Does this power loss theory with an extra dump pipe also apply to GTT R34's??????????????????

Edited by 10MinuteCar
Link to comment
https://www.sau.com.au/forums/topic/217298-is-this-common/#findComment-3866199
Share on other sites

Does this power loss theory with an extra dump pipe also apply to GTT R34's??????????????????

Its even worse on a 34gtt, i dynod one stock, then he came back with a full turbo back 3.5in, and front mount. It gained 5rwkw up top and lost about 30rwkw everywhere else. Put a pfc on it and got it all back and heaps more.

Link to comment
https://www.sau.com.au/forums/topic/217298-is-this-common/#findComment-3866266
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • This. As for your options - I suggest remote mounting the Nissan sensor further away on a length of steel tube. That tube to have a loop in it to handle vibration, etc etc. You will need to either put a tee and a bleed fitting near the sensor, or crack the fitting at the sensor to bleed it full of oil when you first set it up, otherwise you won't get the line filled. But this is a small problem. Just needs enough access to get it done.
    • The time is always correct. Only the date is wrong. It currently thinks it is January 19. Tomorrow it will say it is January 20. The date and time are ( should be ! ) retrieved from the GPS navigation system.
    • Buy yourself a set of easy outs. See if they will get a good bite in and unthread it.   Very very lucky the whole sender didn't let go while on the track and cost you a motor!
    • Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
×
×
  • Create New...