Jump to content
SAU Community

Please Help! Vic R34 Gtr Engine # Doesn't Match?!?!


Recommended Posts

Hi I am planning to buy a R34 GTR private sale.

The steel plate with the VIN/Engine number in the rear left engine bay is stamped/engraved.

I read on this forum that if it is engraved then it might be stolen - factory plates have the details PRINTED, not engraved on them.

The VIN matches what Vicroads tells me, but the engine number is not the same as that stamped on the plate. The guy told me not to pay any attention to that as that was the stamp in Japan, and the engine number would be different in Australia?!?!?!

He is sure the engine hasn't been swapped.

The compliance plate is a red/mauve printed plate on the left hand side of the engine bay, about halfway down.

Just wondering what you guys think about this, is it dodgy? I was originally planning to buy it in the next few days.

Cheers. Any advice would be greatly welcome.

GEt the engine number off the block and call vic roads. If it has been registered before they will have record of it and can also tell you if it's a stolen motor.

The original engine number will also be on one of the ID tags in the engine bay. check that the number on the block matches that tag.

Engraved VINs are fine.

I've had a few cars like this.

And even if the engine number doesn't match (provided it passes a 'stolen' check) that's fine also, the engine could have simply been replaced (however, whether

you want to buy a car with a swapped RB26 is a different issue.)

Thanks that's good advice.

Dave1200, do you know where I can find this engine ID tag in the engine bay of a 2001 Series 2 R34 GTR non-vspec???

I didn't see any other tags apart from the VIN plate and compliance plate, but I wasn't looking for any, so I might have missed it.

Cheers.

Thanks that's good advice.

Dave1200, do you know where I can find this engine ID tag in the engine bay of a 2001 Series 2 R34 GTR non-vspec???

I didn't see any other tags apart from the VIN plate and compliance plate, but I wasn't looking for any, so I might have missed it.

Cheers.

Dave is right, it will be on the block also. Try the front to start with underneath the cams but if not either side by down through the gaps.

Found this thread:

http://www.skylinesaustralia.com/forums/N1...umber+R34+where

It might pay to use the software some of the guys have access to on here, think it is nissfast.

Can you PM me the car out of interest please. Don't worry not going to buy it instead!

if you call 131171 and use the prompts to check a vehicle....all you need to do is say the reg number and the recorded voice at the other end will tell you the VIN,engine number,date of reg expiry and if it been through the VIV system ect.......its a 24 hour system so you can do it anytime.....just give them the reg and it will sing like elvis giving anyone the details of your vehicle,i actually think its a breach privacy myself and shouldnt be allowed.....imagine the amount of false-e-fying you could do and shit you could get innocent ppl in

Edited by ylwgtr2

Before you hand over your hard earned. If you suspect it is stolen, look into it as much as you possibly can and if you find it doesnt match up then report the seller or just forget about it and look elsewhere, its not worth the loss if it turns out to be stolen.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • What bedding in procedure did you use?   When you say stutter, what exactly do you mean? Like it feels like someone letting go of the brakes momentarily and regrabbing them again to get you to stop? Re-reading your post, and that is what it kind of makes me think you're explaining, like theres a little bit of a jolt, likely just as you're reaching a stop. I've only had this issue once. And if its caused by what caused mine, you will want to get the car up on stands again and check it over. Mine was a case of a caliper mounting bolt coming out and letting the caliper rotate on the other remaining bolt and gave play in a wheel as it came to a stop. But not every stop either!
    • Yeop... binned it   This will be a summary will not many pics atm and cbf  Fixed the samsonas - it was totally munched Put a new precision 7675 T4 on with proper split pulse mani Got to Sydney to get to car - drove to canberra to get racecar - drive back to sydney that night Next day all day at Plasmaman putting on new clamps cleaning some things up and adding another large engine oil cooler sitting at the rear above diffuser to keep things cooler Next day - Tuesday - on Dyno - killer wikid awesome pumped out really good numbers - more mid range and on lower boost levels Wednesday - first prac - all day again getting the suspension right - had to borrow front suspension again - out do a lap come in - out do a lap - in - what i had just couldnt handle the load at the more consistent higher speeds - got a lap in at the end of the day that was pretty reasonable  Put it this way that lap wouldve had me in 4th in Pro am for the whole event - with only 700 hp and used tyres Thurs first official prac day - lap out warm up - then entered a hotlap with above setting and 80% effort took corners 1,2,3 and into 4 car felt awesome -  rear came around out of nowhere bang into the wall near front on at whatever 140 kmph Done, over, gone Just one of those how did that happen apparently as all indications show nothing out of the ordinary Got to spend the rest of the time at the event like I hadnt done before - was actually Ok mainly as I had my family and my boy is 9 and got treated like a rockstar Long trip home, lost a trailer wheel in nowhere land, X5 airbag suspension gave up half way across nullabour and rode on bumps stops (its now completely fine) had to do a 19 hr drive day on day 3 as accommodation got screwed up so just had to keep driving till found a town with some Now to reassess - hopefully the motor and other things are OK but yet to be seen too. There is no easy fix there is no i'll just order that part and get it sent - we'll have a talk to people see what can happen and what the go is but at minimum its rebuild from scratch struts forward and alot of time effort and $ should and if I return and if but maybe/ when  I have the cage tied into the front strut towers - if I didnt have that things couldnt been worse you can say its just a front end but if you know what goes into these cars... you'll know what that actually means in reality   Car was very fast. Disappointing we just didnt get to show it Effort doesnt win you races though     Apparently this is motorsport !  
    • Thanks, will do that.  Thankfully they still feel great.
    • Yeah man, absolutely. You can try pushing me all the way in swapping the R34 for an E9x M3 
    • It's almost certainly going to be some amount of pads compound transfer onto the rotors. It will probably go away after you've run them for a bit. If not, pull it all out, lightly sand the rotors, scuff the pads, and rebed.
×
×
  • Create New...