Jump to content
SAU Community

Recommended Posts

  • Replies 92
  • Created
  • Last Reply

Top Posters In This Topic

back together again!!

only a few loose ends to tidy up and she's ready for dyno tuning Friday afternoon to handle the bigger injectors :P Justin at Competition Tuning and Performance will be doing the tuning.

also thanks to Mobile Auto Hoses for helping us out a little with the cost of the turbo lines.

upgrade.jpg

congrats to Beau today who made it through to the top 12 in Driftstate at QR today.

He qualified in 17th position out of 24, then won his first battle after a re-run. Then in his second battle, he drove the car out of sight, but the other car simply had more power and Beau couldnt keep up.

However I was very happy with the way he drove and once we get a chance to put a big power motor in the drift car, I am confident that Beau will do really well in future events.

there was about 8 other cars there over 400hp@rw , I lost to a 415rwhp 2.2 tomei 180sx that is about 970kg , mind you he is bloody good too , just finished 5th two weeks ago at DA Adalide

Had the QLD r2 State championship on sunday , first time driving it with it's new setup turbo , it was a shame I had to take off my tower brace to fit it on as the front seemed to wash out a little coming out of a turn , and I have lost my 2nd gear sycros .

So had practice from 10 , got about 3 laps in and found I was lossing power , opened the hood and found out I had melted a cooler pipe as it was too close to the manifold , so had to rush around to the supercheap to buy and then fit a new one , and also make a section of heat shield to make sure it does not happen again .

Then came qualifiying , I had one more practice lap to check the setup which felt good , so I lined up for my first qualifying lap , started out great but I missed 3rd going into the dipper and went into 5th , but managed to recover and get through without to much trouble. My second qualifying went well besides a little bit of dirt turbo .

Ended up qualifying in 17th and had my first battle up against the TOKAGE soarer driven by Josh Botcher , a well proven driver who normaly drives his FC rx7 , but due to brakege was picked to drive for the TOKAGE company.

First lap I was chasing , and I managed to stick very close but at the cost of losing angle a few times , lead lap I hit the dirt once which was being judged very harshly , so it went to a re- run where as the Soarer spun both times due to a bad tyre , so I was through to top 16.

Next battle was against my very good friend Eugene in the Federal/Mercury 180sx , a seasoned DA competitor in a 400rwhp 2.2 tomei 970kg fully built drift rig. First lap I was chasing and lets just say he pulled away with his foot to the floor , and on my lead lap he followed very well , so I was knocked out , but was told by many people that it was a very close battle considering the power difference. I was told later that with my score against Euge that I made 12th place

  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
    • I have more than enough digging, laying blocks, moving gravel, airrating, feeding and top soiling the grass, and setting up the veggie gardens growing some seedlings,  and then removing all the unused rock to keep me busy for the next few months at least,  hopefully the rain stops soon so I can get a few hours in this arvo, but, before that Sunday is washing day, is every body happy, you bet your life we are Nice country road day drives are a day off whenever I'm muscle sore from all the landscaping at the moment, but, more epic multiple day drives will start once the majority of the big jobs outside are completed
×
×
  • Create New...