Jump to content
SAU Community

Reason For A R35 Sedan ... Cadilac 4dr = 7:59s Nur


Recommended Posts

Did a quick search but didn't see any comment elsewhere about the 2009 Cadi, so ....

Just seen a few sites about the Cadilac being the fastest sedan around the Nur, 7:59 seems legit so far... should spark some interest in the brand before it hits OZ again. Not sure about the looks but it certainly would be hard to miss!

maybe this might provide the incentive for a Nissan to make a 'GTR' based sedan!

http://www.wheelsmag.com.au/News/Cadillac+...ing+record.html

http://www.topspeed.com/cars/car-news/-cad...59-ar57237.html

Maybe Nissan should take it to BMW and Mercedes too... couldn't be a bad thing could it?

post-4838-1211087894_thumb.jpg

Edited by gts4diehard

Don't think it would "fit" with the companies' profile they've built for the GT-R being a homologated race car you can drive on the street.

Maybe a beefed up version of the v36 skyline sedan? or the Cima I think it's called (m35 it's called in the U.S), they'd be similar in size to the cadi.

Edited by Yo-Yo

Autech should make an R35 GTR sedan but then that would be quite hard seeing the R35 is only a coupe and they cant use a sedan version like they did with the 33 i think it was

  • 2 weeks later...

correct...

wonder what the handling was like in the sedan models...

33 sedans arent they much longer than the coupe's... like 30cm or something rediculously close.

anyone with a better memory and the factual answer handy?

Don't think it would "fit" with the companies' profile they've built for the GT-R being a homologated race car you can drive on the street.

The R35 is a homologated race car? For which series?

The SuperGT car doesn't share the drivetrain with the roadgoing vehicle, and its that drivetrain that makes the car. Does anyone know what engine the GT500 car runs? I can't find any info on whether its using a VR block, or retained the VQ block from the 350Z/R34 JGTC cars.

Coupe = Overall Length [in. (mm)] 178.9 (4545)

Sedan = Overall Length [in. (mm)] 180.3 (4580)

so 35mm (1.4 inch) difference if you want to get precise.

yeh im getting heaps of different readings, mainly the coupe changing, between 4530 and 4550, owell, doesnt really matter.

The R35 is a homologated race car? For which series?

The SuperGT car doesn't share the drivetrain with the roadgoing vehicle, and its that drivetrain that makes the car. Does anyone know what engine the GT500 car runs? I can't find any info on whether its using a VR block, or retained the VQ block from the 350Z/R34 JGTC cars.

the GTR uses a 4.5ltr V8 developed for the 350z in the 2007 season.

Righto. So neither the powerplant nor the drivetrain from the GT500 GT-R is shared with the R35.

So I'm wondering if Yo-Yo can tell us which series the R35 GT-R is homologated for. I'm actually curious, because I'd love to see how the car goes and what its racing against. The only motorsport I've heard the R35 do is Targa Tas, so far.

  • 2 weeks later...

Linky.

Nissan execs have also confirmed that the GT-R is an unprofitable model but the introduction of vehicles based on the same platform will help change that. In addition to the Spec V, the platform is expected to yield a model for Infiniti due for release in less than a year.

More information that a PM platform sedan is probably in the making. I can't see what else they could build on the relatively expensive PM platform that would see a good return aside from a M5/E63/RS6/XF-R/CTS-V decimating Infiniti super sedan.

I just hope no-one slaps a GT-R badge onto it as a result.

Did a quick search but didn't see any comment elsewhere about the 2009 Cadi, so ....

Just seen a few sites about the Cadilac being the fastest sedan around the Nur, 7:59 seems legit so far... should spark some interest in the brand before it hits OZ again. Not sure about the looks but it certainly would be hard to miss!

maybe this might provide the incentive for a Nissan to make a 'GTR' based sedan!

http://www.wheelsmag.com.au/News/Cadillac+...ing+record.html

http://www.topspeed.com/cars/car-news/-cad...59-ar57237.html

Maybe Nissan should take it to BMW and Mercedes too... couldn't be a bad thing could it?

im fairly certain Nissan wouldn't have much trouble building a 4 door production sedan to beat that time. They can probably do it with their eyes closed, it just that there doesn't seem to be much point in building such a fast 4 dr sedan. For one, you'd have to stiffen up the suspension which would make it less comfortable, thus less appealing to mass market.

it just that there doesn't seem to be much point in building such a fast 4 dr sedan.

I'd say there is.

Nissan's trying to grow Infiniti into a proper Euro competitor, especially now that they're launching the brand in Europe. They've got the V35/V36 to go against the 3 Series and the new FX to compete against the X5.

The Germans practically own the super-sedan class with the M5, RS6 and E63 (and to a lesser extent the M3, RS4, C63 and IS-F, against which the current Skylines can't really compete). Since Infiniti can't have the GT-R, I'd say a super sedan based on the PM platform as a halo model would be a much better fit.

For one, you'd have to stiffen up the suspension which would make it less comfortable, thus less appealing to mass market.

Well, the R35 does a 7:29 with its "quite firm" setting. Even with more weight, a longer wheelbase and slightly less power from the engine, you might still be able to keep the difference to under 30s a lap. The suspension in the PM is adaptive. You could set up the "comfy" setting to be a lot softer than the GT-R's equivalent setting in line with its competitors, and firm up the car when the driver flicks the R switch and actually wants to go fast around corners.

post-50046-1214324403_thumb.jpgpost-50046-1214324424_thumb.jpg

im fairly certain Nissan wouldn't have much trouble building a 4 door production sedan to beat that time. They can probably do it with their eyes closed, it just that there doesn't seem to be much point in building such a fast 4 dr sedan. For one, you'd have to stiffen up the suspension which would make it less comfortable, thus less appealing to mass market.

The Cadillac 'production' vehicle seems to have some type of bracing and different seats? Hmmm....

i think you'll find the wheelbase is exactly the same though. the only skyline model to have a different wheelbase between sedan and coupe was the R34.

For prior cars. But if they're developing a sedan based on the PM platform, it probably won't. For example, both the Z33 and V35 are FM platform cars but the wheelbases are different lengths. "Platform" doesn't necessarily mean the physical chassis. It means engineering hardpoints, like suspension and drivetrain design.

Since the R35 has been panned as being a bit cramped for rear passengers, were they to make a PM-based sedan it would have to be longer than the GT-R to meet the minimum comfort requirements for this class. The GT-R isn't exactly a small car, and so a sedan variant based on the same platform is going to be more M5 sized than M3.

4 door R35?? NOT. GONNA. HAPPEN. The V35/36 and the R35 are totally different cars.

No shit, Sherlock. No-one's talking about adapting the V35/36 chassis to fit the R35's AWD drivetrain. They're talking about using the GT-R's PM platform to build another car. It will sit above the V36 in size.

And yes, other cars built around the platform the GT-R uses will be released. Pray that they're building a sports sedan, because if they're not that only leaves a SUV or some even worse prospect....or lose money, at which point they'll just can the entire GT-R project.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...