Jump to content
SAU Community

Recommended Posts

3 is nothing

knock is the engine pinging or detonating etc...

the factory warning is set at 60, which is when the check engine light will flash on the dash...anything up to about 30 is ok. If it starts hitting over 30 you might want to get your tuner to look at the tune...

yeah. The mic can often pic up vibrations (not in the engine) and register high, keep driving and see if it's a once in a while thing or a common happening, if the later go see your tuner.

i got mine tuned by matty spry.

usually max knock i see is 18.

BUT when i redline it or go a tad over redline it shoots up to 60+...and the warning lite goes off, because he set it that way.

now he said "when u reach the redline or go over it the knock will shoot up. ignore it. its normal"

is THIS true?

The old knock reading mines been up to 133 & gets up to about 60 everyday but had ears on it with a knock detector & we hear nothing so yeah mine might registering my dog box or something else so i wouldnt worry about 3 lol. On start up knock may read a little high.

every time i hit limiter knock reads anywhere from 70 - 120. i try to stay off the limiter. Yes it is normal

i got mine tuned by matty spry.

usually max knock i see is 18.

BUT when i redline it or go a tad over redline it shoots up to 60+...and the warning lite goes off, because he set it that way.

now he said "when u reach the redline or go over it the knock will shoot up. ignore it. its normal"

is THIS true?

go near red line in 4th or actually hit the limiter?

maybe the air is getting too hot and it is detonating a bit.

If your hitting the limiter ignore all knock readings from the limiter. remember stock limiter is 6900rpm.

go near red line in 4th or actually hit the limiter?

maybe the air is getting too hot and it is detonating a bit.

If your hitting the limiter ignore all knock readings from the limiter. remember stock limiter is 6900rpm.

when i reach limiter man. ahhh, well my limiter is set to 7300. that might be the problem. i will just need to hold back.

Hey guys, i wanted to set the rev cut to 7500 on mine, currently its at 8000.....how can i set it to 7500 on my hand commander, my tuner told me its really easy and somethingi can set up myself.

Also, i didnt know what it was set at before, and i was driving it hard once, and the car kind of jerked really badly (after going high reves, possible over 8000), was that my rev cut doing this, is it safe to hit rev cut...i guess its better than going over the rev i guess.......

Thanks:)

go to settings, then scroll to the last option which is rev. then hit the right arrow so the revs are highlighted then hit down arrow till it's down to what you want. then just hit back and go back to monitor mode or whatever you normally leave it in.

My Mates r33 would contantly register about 80knock on hard driving, the tune was spot on and great. Had a look in his engine bay and his sway bar had a massive dent in it from the intake hitting it, removed it and on full thrash he registered knock of 30. Big change.\

Knock is recorded as any metallic sound as in metal hitting metal, 3 is nothing.

Story pointless just a lil fyi

Edited by DECIM8

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have a look at that (shitty) pic I posted. You can see AN -4 braided line coming to a -4 to 1/8 BSPT adapter, into a 1/8 BSPT T piece. The Haltech pressure sender is screwed into the long arm of the sender and factory sender (pre your pic) into the T side. You can also see the cable tie holding the whole contraption in place. Is it better than mounting the sender direct to your engine fitting......yes because it removes that vibration as the engine revs out 50 times every lap and that factory sender is pretty big. Is it necessary for you......well I've got no idea, I just don't like something important failing twice so over-engineer it to the moon!
    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
×
×
  • Create New...