Jump to content
SAU Community

Recommended Posts

Hi all,

I have an r34 sedan non-turbo (not using turbo brakes like in the GT-V).

My rotors are in need of being replaced soon and I'm tossing up between slotted rotors or just the plain (genuine) ventilated rotors. I want to know if it is worth spending extra for the slotted rotors (DBA 4000 series) or if I'm just wasting my hard earned $$$. I'm intending to do all 4 corners. I mainly do city/freeway driving, on the odd occassion i take my car out to the Black Spur or the Great Ocean road for some fun (guys in Victoria would know these places :P )

Also wondering if there is a difference on the life of the rotor (slotted vs plain).

What are the recommended pads to go with the rotors? I was thinking bendix ulimates or would these be too harsh on rotors...

If your going to the trouble of changing the rotors, i would just put in slotted...

You really only need them in the front... however it does look better if you do all 4, and not just 2.

I dont think they are that much more from memory...

Just dont get the ones with the holes in them... augmented i think they are called, as disc around the holes tend to get fine line cracks due to rapid heating and cooling.

so ya +1 for slotted!

There are 4 types. Plain (no grooves or holes), slotted (grooves), drilled (holes) and slotted and drilled (obvious, isnt it?)

Slotted wear your pads down a lot more, but drilled are more prone to cracking. However, the drilled do allow for more venting, so they do serve a purpose

DBAs have a reputation for cracking, even their slotted rotors. I think most of the people doing it are doing it on the track though.

If you're only doing GOR and the Spurs you should be OK. I would assume, and hope, that you're not pushing your car to the limit on either road and overheating your braking hardware. There's not much margin of error available on either road, and with GOR especially help can be very far away.

DBAs have a reputation for cracking, even their slotted rotors. I think most of the people doing it are doing it on the track though.

If you're only doing GOR and the Spurs you should be OK. I would assume, and hope, that you're not pushing your car to the limit on either road and overheating your braking hardware. There's not much margin of error available on either road, and with GOR especially help can be very far away.

Thanks for the tip about the rotors cracking - its got me thinking :)

I try to be gentle on the brakes where i can by using a lower gear.

I wonder if anyone else here has experienced cracking fo non-track use?

  • 2 weeks later...

Thanks for the tips guys. I've bitten the bullet and going for DBA slotted "4000 series" up front and DBA slotted "street series" for the rear. They are on order, I'll update you guys on what I think of them.

get slotted and drilled mate look so much better and a lot better performance, you will not have any dramas with them cracking unless your thinking about drifting or track days ?(unlikely being n/a)

You can also get them cryo dipped (ask your brake specialist about this)

+1 Slotted and Drilled (countersunk)

i havnt really heard much of a difference between the 2 unless u doin some serious racing but my point of view standered ventalated is arite. plus now brake pads dont use aspesdos anymore they use fine metal particals in the brake pad so rotars dont last as long as they used 2. slotted do look better if u got money go for it if not just go normal cause rotars some are luky to last 80000km.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...