Jump to content
SAU Community

Recommended Posts

that exactly what was wrong, clearance for the bearing were wrong anyway in not going to start a dispute with a racepace or anyone

i bought the car off a sau member with the built motor, and my gf rode it of 2 weeks later no damage to the front what so ever,

put the motor in my 32 all bout 20mins running in the car its seized, i dont really care bout it anymore cause my motor is in the process of getting built now

just to make a clear not i didnt say race pace were shit engine builders, i said it was a shit build i have nothing agaist them, them may have done something wrong them have not, but i was told clearance for the bearings werent correct

your more than welcome to have us look after it for you ali...

doubt Ben would have been responsible for what has occurred.

I hold him and his business (RacePace) in the highest regard.

Edited by DiRTgarage

I'd like to make a few things clear here.

Racepace did build this engine. In 2005.

We did not install it and we haven't seen it since 2005.

It is now onto its 3rd owner who stated it was running perfectly when he purchased the R33GTR that was subsequently written off in an accident.

Later it gets installed into a 32GTR and seizes after 20mins.

Now I'm not pointing fingers at all, but doesn't this sound just a little strange??

We absolutely stand by/warrant our workmanship but it is made extremely hard when you have no control over what happens to your engines years after they are put into service.

We have built hundreds of RB's that see all sorts of use/abuse, so I'm very sorry to hear of this engines demise.

Hope it all works out for you Ali.

cheers,

Ben

Edited by RPMGTR
thx ben im not holding you responsible at all or else i would have called to sort something out,

and i understand its been 3 year since the rebuil so i wouldnt expect you to do anything about it,

thx mate

So why say it was a shit house build then exactly you moron?

Sounds like a case of extreme back pedalling.

Dont PM me about your warning, its clear what its for.

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • The spray cans were in the "Kiln" room whilst I was preping the parts,  so probably around 2 hours to get them warmed up, the kiln room has 3 small ovens running at 100°c, 3 medium sized ovens running 100°c, and the large one I used running at 80°c, the room itself was about 28°c, I also spent a bit of time taping up the parts in the room as well, and by the time I was done I would assume that the parts were around that 28°c As for power, I expect a couple of Killerwasps up high would be achievable with the current mods, I'm still running the MZR 2.0 intake and throttle body, and there is a slight mismatch with the 2.0 intake (smaller) and 2.5 intake ports (larger) on the head, this intake is matched and specifically designed to fix this issue with the ports mismatch, the throttle body is also a couple of mm larger, OEM is 65mm, the Bosch is 68mm In the end it will look "prettier" than the molded plastic thing that is the OEM MZR 2.0 intake As for the LSD, it's the OEM Torsen which works fine for what I use the car for, plus, basically no maintenance apart from the occasional oil change
    • I was at Tunehouse in Marrickville (great team over there really know their VR's) , and I spotted this Very clean R35.  
    • Mate , I have the same issue right now with the exhaust noise , if you can tell me what your local guy did , I'll talk to my guys and see if they can do the same. Power is good but it just too loud when put it down. 
    • The other trick I've found with wrinkle black is to put the can in hot water for a bit to warm the paint up, and to pre-heat whatever you're painting. It'll be interesting to see if you pick up any power with the intake, following with interest. Got a proper lsd for this?
×
×
  • Create New...