Jump to content
SAU Community

Recommended Posts

Hi everyone,

bit of a question here. I was looking to get a FMIC installed and have been shopping around. I was looking for something around the $700-800 mark. I thought the Greddy SpecM's would fit in an R34 GT-T but have been informed by a shop keeper I'll need a Spec-V. Is this the case or have some of you guys got the Spec M in there?

Cheers!

Link to comment
https://www.sau.com.au/forums/topic/222623-greddy-intercooler-on-r34/
Share on other sites

Greddy spec M is out of production. and when they were in production they were very cheap as they use a cheaper core to all the other greddy coolers (still nice piping). $800 for one is pretty cheap. brand new in japan they were around the $400 mark.

I believe they have been replaced now by Greddy LS. but personally I would get something a little nicer. something higher up in the greddy range.

M-Spec fits. I Put one on mine. No cutting of fan req'd. Clearance with the bonnet is a bit of a b!tch, hits a tiny bit but no damage done. Probably the way I fitted it tbh.

Whoever is quoting you 700-800 is ripping you off. Can get them for 600 and possibly 580 or so with a bit of haggle.

Edited by Magic

Yeah i got mine for $600

Magic, you're lucky...i had to trim the fan down a little...

you're right about the clearance. bit of a bitch, but got it to fit.

pretty good fit eventually though...

Edited by ITZTRU

I'll take a pick of my install tomorrow of how to stop it from hitting the fan since I'm pulling crap out while im changing my corroded radiator hose fitting to a stainless one. Bit late in your case, but for guys doing it in the future it's a good idea. Instead of using one of the parts used to mount the fmic up. I screwed a spare onto the left side of the engine so it holds the piping in place solid as a rock. Also, need to remove the Neo engine cover. :thumbsup:

Edited by Magic

I have a Spec M installed on mine. works a treat, no complaints just yet.

Had to trim only like 2cm off the fan which isnt too much. Clears the bonnet, but a pretty big job altogether.

As Beer Baron said, the Spec M has been replaced with the new Spec LS which has a tube and fin core instead of the bar and plate which the Spec M has

I have a Spec M installed on mine. works a treat, no complaints just yet.

Had to trim only like 2cm off the fan which isnt too much. Clears the bonnet, but a pretty big job altogether.

As Beer Baron said, the Spec M has been replaced with the new Spec LS which has a tube and fin core instead of the bar and plate which the Spec M has

Are you sure the LS is tube and fin? From the Greddy advertising I've seen they are still bar and plate, just lighter then the Spec M.

Mmmm, seems like the LS is the way to go indeed. I guess the next question that I beg to ask is, where can I shop for one of these in Victoria? I was looking around a few joints but most say they want 680 (my best quote so far).

Ideas gentlemen?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
    • Heh. I copied the link to the video direct, instead of the thread I mentioned. But the video is the main value content anyway. Otherwise, yes, in Europe, surely you'd be expected to buy local. Being whichever flavour of Michelin, Continental or Pirelli suits your usage model.
×
×
  • Create New...