Jump to content
SAU Community

Greddy Intercooler On R34?

R34_Wong

By R34_Wong,
in Engines & Forced Induction

 Share

Recommended Posts

R34_Wong Mentor

R34_Wong

Posted
Posted

Hi everyone,

bit of a question here. I was looking to get a FMIC installed and have been shopping around. I was looking for something around the $700-800 mark. I thought the Greddy SpecM's would fit in an R34 GT-T but have been informed by a shop keeper I'll need a Spec-V. Is this the case or have some of you guys got the Spec M in there?

Cheers!

Link to comment
https://www.sau.com.au/forums/topic/222623-greddy-intercooler-on-r34/
Share on other sites
Beer Baron Grand Master

Beer Baron

Posted
Posted

Greddy spec M is out of production. and when they were in production they were very cheap as they use a cheaper core to all the other greddy coolers (still nice piping). $800 for one is pretty cheap. brand new in japan they were around the $400 mark.

I believe they have been replaced now by Greddy LS. but personally I would get something a little nicer. something higher up in the greddy range.

Magic Experienced

Magic

Posted
Posted (edited)

M-Spec fits. I Put one on mine. No cutting of fan req'd. Clearance with the bonnet is a bit of a b!tch, hits a tiny bit but no damage done. Probably the way I fitted it tbh.

Whoever is quoting you 700-800 is ripping you off. Can get them for 600 and possibly 580 or so with a bit of haggle.

Edited by Magic
ITZTRU Proficient

ITZTRU

Posted
Posted (edited)

Yeah i got mine for $600

Magic, you're lucky...i had to trim the fan down a little...

you're right about the clearance. bit of a bitch, but got it to fit.

pretty good fit eventually though...

Edited by ITZTRU
Magic Experienced

Magic

Posted
Posted (edited)

I'll take a pick of my install tomorrow of how to stop it from hitting the fan since I'm pulling crap out while im changing my corroded radiator hose fitting to a stainless one. Bit late in your case, but for guys doing it in the future it's a good idea. Instead of using one of the parts used to mount the fmic up. I screwed a spare onto the left side of the engine so it holds the piping in place solid as a rock. Also, need to remove the Neo engine cover. :thumbsup:

Edited by Magic
GMan Proficient

GMan

Posted
Posted

I have a Spec M installed on mine. works a treat, no complaints just yet.

Had to trim only like 2cm off the fan which isnt too much. Clears the bonnet, but a pretty big job altogether.

As Beer Baron said, the Spec M has been replaced with the new Spec LS which has a tube and fin core instead of the bar and plate which the Spec M has

_Scotty_ Collaborator

_Scotty_

Posted
Posted
I have a Spec M installed on mine. works a treat, no complaints just yet.

Had to trim only like 2cm off the fan which isnt too much. Clears the bonnet, but a pretty big job altogether.

As Beer Baron said, the Spec M has been replaced with the new Spec LS which has a tube and fin core instead of the bar and plate which the Spec M has

Are you sure the LS is tube and fin? From the Greddy advertising I've seen they are still bar and plate, just lighter then the Spec M.

R34_Wong Mentor

R34_Wong

Posted
  • Author
Posted

Mmmm, seems like the LS is the way to go indeed. I guess the next question that I beg to ask is, where can I shop for one of these in Victoria? I was looking around a few joints but most say they want 680 (my best quote so far).

Ideas gentlemen?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • perry_r33
      R34 GTR Vspec Garage Sale - All must go!

      By perry_r33 · Posted

      Pm sent 
    • Robot
      Skyline v36 350GT sedan hunting on idle

      By Robot · Posted

      Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...