Jump to content
SAU Community

Recommended Posts

Hi all, I'm looking to take a bit of a step back in time, I'm selling my R34 and am currenlty looking at a KPCG10 GTR replica.

In all honesty I don't know a whole lot about them but I really like them. I'm not seeing a whole lot of info around on them, it's almost like not many people in Australia have them.

Can anyone give me any good advice or point me in the direction of good web pages etc?

Thanks in advance! :(

there was a site which one of j-spec's customers ran, dedicated to oldschool jap cars, but i forgot the URL

try japanesenostalgiccar.com for info.

as for compliance, not much has to be done, just a roadworthy and an engineer's inspection. if its pre 1978 it doesn't haev to be RHD, if its pre 1983 (i think, not sure) it doesn't have to meet some EPA requirements, and if its a lil older it doesn't have to meet any. Not sure on the year the rules kick in though. can check if you want.

Adz, send craig (J-Spec Imports) a PM on sau, he'll respond eventually.

Check out this thread on Japanese Nostalgic car.... I think the car might actually be from melbourne aswell.

>>>Project Hakosuka<<<

Plenty of useful information.

good choice, every man and his dog has a 34 now...

  • 4 weeks later...

Hi Adzmax,

There are seven in Australia (known). Two basically unmolested KGC10s, four GT-R replicas, one of which may be for sale (Sydney) . These have been built in Japan from either a standard GT or GT-X. In W.A. one radical ,big flares, big wheels, loooow, etc also may be for sale. See C-red tuning, is also an importer of Japanese parts .

Have a good read of Kevs Hakosuka rebuild thread. Throw some questions to Kev. He has recently done what you propose. All care was taken to source a good car through a (still!) respected importer. Kevs is not the only case like this. It is a risky business, I was just plain lucky.

KGC10 = 1971-72 Nissan Skyline GT 2 door ( & GT-X)

KPGC10 = 1971-2 Nissan Skyline GT-R. The real deal with the S20 and the other 10,000 parts that make it GT-R, around $100,000 in round figures for what I would call a good car.

I can put you in contact with the owner of the car that MAY be for sale in Sydney.....or is it a KGC110 your after?!

Cheers :P

that would be nathan from Mt White automotive's car, and it is in beautiful condition. give him a call directly if you are genuinely interested. I would love to have the space to buy it.

Hey all, have missed the added posts in the this thread :thumbsup:

72GT - Still learning about these cars, yes it's actually a KGC10 2 door I'm after, ideally I'd love to do a nice tasteful GTR mock up. God knows I couldn't afford a real KPGC10 :banana:

Terry/Duncan - Looks like a nice car, plenty of goodies too! What's the best way to get in contact, might be worth a flight :yes:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
×
×
  • Create New...