Jump to content
SAU Community

Recommended Posts

  • 2 months later...

Intake temp sensor: 22630 - 95L00 ---- $160

Exhaust temp sensor: 22740 - AA300 --- $ 380

These were the prices that i paid.

:ninja:

And yes if you are doing a MFD in GTT etc as i did then you need to drill and mount the intake sensor in the intercooler and get

a female thread welded on your dump pipe for exhaust temp sensor.

Now do keep in mind that if you are doing this to a non Vspec GTR then it may be a better option to pay $ 600 more and get the Nismo

upgarde V2 for the MFD (PART: 2371B-RSR48) as it comes with the Exhaust sensor, You then get the bonus of higher boost (2 bar), oil pressure on MFD, G sensor, lap timer and data logger software.

Edited by 99 GTT
  • 10 months later...

Installed mine this week-- thanks very much for the above info everyone!!!

i mistakenly connected pin 46 instead of 45 to the AMB to show AMB intake instead of nothing and by using amb into 46 being exhaust temp it shows a reading of 500-610 range according to temp for exhasut temp. i then added pin 45 too and has a AMB temp for intake and also an exhasut temp reading-- now i know this isnt the real temp for either but it shows something rather than nothing. Also interseting to note the mfd must use te signal sent from the sensor and do something wht it to present its reading----for example i had the AMB reading 8 degrees through intake, and while wired to exhaust it read about 580 degrees... so the samesignal sent by the sensor is interpreted differently by the mfd. I know having these wired up isnt the correct plg so incorrect temp readign, but at least it isnt showing nothing anymore :)

  • 4 months later...
  • 5 months later...
  • 3 months later...
  • 1 year later...
I decided to keep my MFD after not receiving solid buyers.
MFD-1.jpg
custom panel to keep the buttons in-order.
MFD.jpg
I decided to remove the "MFD" characters because I'll purchase a FULL-RACE ETS PRO unit and use the space to place the switches and knob.

My only beef is that I don't have oil pressure per not having the MFD2 update by NISMO. I haven't decided if I want to upgrade to the NISMO version or if I just want to purchase a dedicated oil pressure gauge. I'm not a fan of gauges but I do have an AEM AFR gauge...

Anyway, does anyone know how the MFD 2 reads oil pressure? Does the system come with an additional oil pressure sensor?
http://www.nismo.co.jp/en/products/competition/ie/pdf/ie01.pdf

i didn't find anything on NISMO's site.
  • 2 years later...

This is an amazing thread, much appreciated! I am currently collecting the last few parts for the MFD in a 4 door w/ R33 RB26. The only problem I am having so far is when I cut into my dash [i dont have the gauges] I am not sure if the 2 metal brackets will be there or not. Can anyone shine a light on these things?

Ive found some pictures that show that the brackets are not part of the metal bar below the dash, and when the dash is pulled out these brackets come with it. I am assuming the triple gauge brackets and MFD brackets are the same, but Im honestly not sure.

Again any info would be greatly appreciated!

Pic of brackets in removed dash:

Photo2003.jpg

Edited by tommytomatoes
  • 1 year later...

Would like to add a few thing to this thread after my install a while back and learning a few things online.

Standard R34 GT-R only displays 5 rows of data on mfd, V-spec I/II/M/Nur/N1 comes with 7 rows of data, normal GT-R does not display intake and exhaust temp data. Most people already know that getting the Nismo v2 mfd upgrade will get intake and exhaust data (comes with exhaust sensor) as is what I have.

There are ways to display 7 rows of data on standard GT-R without buying the exhaust sensor or the Nismo upgrade. As all R34 GT-R comes with intake temp sensor, you will see it on your intercooler driver side. The exhaust temp sensor connector is on the passenger side next to turbo outlet, you will see a female connector with 2 holes in it. This is where the exhaust sensor hooks up, however if you don't have the exhaust sensor and still want to display 7 rows all you have to do is get a wire and plug it into the connector by shorting it and then running the self diagnosis. You should now see intake temp values and --- for exhaust temp if you don't have exhaust sensor.

This is probably the best and easiest way as you don't have to take out your mfd and jump wiring the back. I have not tried this personally but this youtuber has got it working.

Credit goes to this youtube video:

 

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...