Jump to content
SAU Community

Recommended Posts

Im looking at fitting an aftermarket Steering Wheel like a momo Race to my R34 GTT, i heard some ppl say i can use a standard Boss kit and others say i need a boss kit with Hicas, can someone please help me out here to what i need.

Im also looking at fitting a Quick release hub so i can remove the steering wheel.

Any Info would be greatly appreciated to what i need to do all this,

i did try a search but couldnt find any info related to my question.

cheers and thanks

David

Id just take out the light in the dash, you've got the wheel off its like 4 screws.

Problem with fuse is in a crash ur passenger bag would want to work cause if it dont your passenger will have a nice head scar.

If you want to get technical there is a clip attached inside the wheel, this needs to be grouned. just attach a wire on a clip ground it to the wheel screws :D

Ill snap a photo if I take it off again.

Edited by DECIM8
  • 2 weeks later...

Horns pretty simple, I tightened the wire under the main bolt. One question though, why replace an airbag wheel with something like that? IMO the stock wheel looks much better.

I have a MOMO Commando on mine, racey and fancy, but not overly "out there"

Thanks guys for the advice, all good.

I decided to go with the momo because it was a cheaper option than buying a brand new 34GTT airbag wheel in mint condition - my current 34GTT wheel is peeling, plus i didnt pay for the momo wheel, so its all good.

this is probably a very stupid question .. but none of these aftermarket steering wheel support the standard airbag right ??

hmm.. I sence a very important neice market comming along!

Thanks all for the advice, the new wheel is on now and the horn works no problem ,airbag light is fine got the boss kit with the plug etc so very pleased, the steering wheel does protrude out slightly more than normal because of the D1 Quick Release hub but its not that noticable only when flicking the indicator on you need to extend your finger a little (not the lazy flick like normal while holding the wheel)

here is a couple of pics,

cheers,

David

post-7461-1218165360_thumb.jpg

post-7461-1218165383_thumb.jpg

post-7461-1218165402_thumb.jpg

  • 5 weeks later...
  • 1 year later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drive beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • i will be there 😁
    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
×
×
  • Create New...