Jump to content
SAU Community

Recommended Posts

i'm trying to remove the tail lights from my 32 to get the water out of them, but i hit an obstacle fairly early on. how do you get these things out? i only managed to get one out by very lightly unscrewing it but that doesn't seem to be working on the others ;) thanks!

post-29555-1218181337_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/231539-how-the-f-do-you-get-these-out/
Share on other sites

yah, they're bitches... turn once to 'unlock' it, then pull... Once it is free spinning, that means it's unlocked, no amount of anti-clockwise force will help you...

Very easy to break too... so careful on the pull...

LOL! Yep the good old plastic screw...

As you unscrew them, you might need a very thin / fine filer or flat head screw driver to help hinge it out as your unscrewing it.

See how you go.

don't worry too much, you can get replacements from repco. if you can't get it out without damaging it, just cut it off with a pair of side cutters are replace it

orly ???

hahah i would have replace3d them ages ago if i new that hahahaha

best bet if you can get to the back of them is simply apply force to the side of the part you cant see ... engages the thred on teh screw more to allow them to be unscrewed with a driver - also dont put any force down on the screwdriver as you try to undo them

there was much bloodshed, sweat and profanity, but i got them all out. in my defence, i'm not a complete noob. i just wondered if there was actually some awesome way to do it that i wasn't aware of. sadly not.

wedge a very thin nail file or pin in the smaller circle which seperates the screw and the casing then force it up as you unscrew
...engages the thred on teh screw more to allow them to be unscrewed with a driver - also dont put any force down on the screwdriver as you try to undo them

^^ 1000%

Though most the time you cant get to it from underneath, so use a feeler gauge, or small screw driver to put some load on the spliced bit, just enough force to get the thread to grip again.

Worst case do Bluey33's method, but that will most likely mark the plastic.

And yah, you can get replacements from anywhere... getting the exact shade of grey can take some searching though.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...