Jump to content
SAU Community

Recommended Posts

  • 2 weeks later...

Thanks. Yeah not sure if I will continue to whore wheels after this!

19x8.5 +25

19x9.5 +30

Wish I can slam it further but mrs would kill me.

Might go and buy a sortaflush sticker :)

That looks seriously good!!

Are the back tyres thicker than the front? It looks like the front is lower, but not sure.

That looks seriously good!!

Are the back tyres thicker than the front? It looks like the front is lower, but not sure.

Thanks. Yeah fronts are 245/35 and rears are 275/35 so yes, rears are a slightly taller profile. Ideally the fronts should be 245/40, but the tires came with the wheels so I will use them until they run out before changing.

It's been a long time since i took some photos of my car. So me and my new house mate cleaned our cars and went for a drive and got some nice shots :thumbsup:

The first place we took phots was at the "Sydney Memorial" Then it was out to the light house (my other house mate said it looked like a cock and balls) :/

After the cock and balls shot we drove around the corner to "Separation Point" for some sunset shots. My fav photo is the one with my car by it's self, LOOKS GREAT :thumbsup:

post-60315-0-08962200-1319380788_thumb.jpg

post-60315-0-72524000-1319380899_thumb.jpg

post-60315-0-11941100-1319381006_thumb.jpg

post-60315-0-90139700-1319381099_thumb.jpg

post-60315-0-30208600-1319381228_thumb.jpg

post-60315-0-25098400-1319381302_thumb.jpg

post-60315-0-26338900-1319381421_thumb.jpg

post-60315-0-19847700-1319381511_thumb.jpg

post-60315-0-23239700-1319381629_thumb.jpg

this is a very nice shot

Agreed. :thumbsup:

It's been a long time since i took some photos of my car. So me and my new house mate cleaned our cars and went for a drive and got some nice shots :thumbsup:

The first place we took phots was at the "Sydney Memorial" Then it was out to the light house (my other house mate said it looked like a cock and balls) :/

After the cock and balls shot we drove around the corner to "Separation Point" for some sunset shots. My fav photo is the one with my car by it's self, LOOKS GREAT :thumbsup:

Looking good there, Paul. When you getting new wheels, mate? I think it's long overdue. :)

Edited by VNS 24

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...