Jump to content
SAU Community

Which Hks Pipe Kit Am I After.....help!

Bakes

By Bakes,
in Engines & Forced Induction

 Share

Recommended Posts

Bakes Mentor

Bakes

Posted
Posted

I want the HKS pipe kit like the one I have attached as a picture of it installed in someones car. The kit needs to be able to fit onto my stock intercooler and stock turbos, R34 GTR.

I want the whole kit, ie: hard pipe from both sides of the intercooler to the throttle on the left side (if u are facing the engine) and all the way to each turbo and then out to pod filters.

Which kit am I after from the list below? Or do I have to buy a combination of kits? Is the first one on the list what I am after? (I have HKS pods already but dont mind getting new ones If they are part of the kit)

If you know, please respond with the model number as listed.

Thanks and please excuse my ignorance on the subject :P

HKS Type SPL kit - part number:1302-SN034 (pic attached)

This kit runs all the way to throttle from air filters.

Comes with 4 Suction Pipes + 5 IN Pipes + 2 OUT Pipes + 2 Re-circulation Pipes

Also comes with HKS sport air cleaner(Super Power Flow).

HKS Type SPL kit - part number:1302-SN035

This kit runs all the way to throttle from air filters. After market air filters required.

Comes with 4 Suction Pipes + 5 IN Pipes + 2 OUT Pipes + 2 Re-circulation Pipes

HKS Type SPL kit - part number:1302-SN036

This kit runs from air filtyers to turbo & from turbo to intercooler.

Comes with 4 Suction Pipes + 4 IN Pipes + 2 Re-circulation Pipes.Also, comes with HKS sport air cleaner(Super Power Flow).

HKS Type SPL kit - part number:1302-SN037

This kit runs from air filters to turbo & from turbo to intercooler. After market air filters required.

Comes with 4 Suction Pipes + 4 IN Pipes + 2 Re-circulation Pipes

HKS Type I/C kit - part number:1302-SN022

This is a kit to replace factory rubber hoses from turbo to intercooler & from intercooler to throttle.

Comes with 2 IN Pipes + 2 OUT Pipes

Buff finish

HKS Type I/C kit - part number:1302-SN023

This is a kit to replace factory rubber hoses from turbo to intercooler & from intercooler to throttle.

Comes with 2 IN Pipes + 2 OUT Pipes

Chrome finish

post-43290-1220405740_thumb.jpg

post-43290-1220406401_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/234541-which-hks-pipe-kit-am-i-afterhelp/
Share on other sites
Bakes Mentor

Bakes

Posted
  • Author
Posted

The kit in the 2nd pic in my thread looks to have everything you are talking about Paul, or am I wrong???

I dont know If I need to buy one of the top two items in my list only (SPL kit), or If I have to buy one of those plus one of the I/C kits also at the bottom of the list????

Bakes Mentor

Bakes

Posted
  • Author
Posted

Does anyone rekon my current pods would fit the kit, and more importanty inside the engine bay as the 2nd kit is obviously cheaper as it comes without pods. Or should I just aim for the 1st kit which comes with the pods and is ~120 bux dearer. My current pods are attached, they are HKS pods

post-43290-1220432576_thumb.jpg

Martin HKS Enthusiast

Martin HKS

Posted
Posted

Yep, you need the 1302-SN034. I love the old HKS Metal Flow Filters but unsure if they will fit with the Special Full Piping Kit (distance from AFM to inner guard with piping kit may be too tight for them). I'm pretty sure I have one in stock for the R34 if you want me to check. Drop me an email at work tomorrow and I'll let you know how much (about $1550 from memory). It's [email protected]

Cheers

Marty

Martin HKS Enthusiast

Martin HKS

Posted
Posted
The racing chamber kit does include the pipes from filters to turbos as well as the pipe that has twin turbo written on it and the ic y pipe. The hks catalog confirms it

Wrong. The Racing Chamber kit does not include pipwork to the turbo from filters. The picture in catalogue/website is Racing Chamber and Racing Suction Kit together.

Cheers

Marty

Beer Baron Grand Master

Beer Baron

Posted
Posted

personally I would go the trust kit (and I have, twice!).

I think I just like the more artistic shape of it. I had it on my old 32 and just bought it for this one i'm building too. it's a nice kit.

p3sxm1.jpg

Bakes Mentor

Bakes

Posted
  • Author
Posted

What will the HKS kit do for my performance? I mainly want it so that there is no chance of me blowing one of the lower rubber hoses off as I run 1.2 bar and also because I love the look of the full kit.

I have HKS EVC, HKS Hi Power exhaust, Nismo fuel pump, Nismo fuel pressure regulator and HKS pods at the moment. Stock everything else.

Will I have more lag, less lag or same lag If I put the full kit on?

Will I have same power?

Thanks

R33GTRKid Experienced

R33GTRKid

Posted
Posted
Wrong. The Racing Chamber kit does not include pipwork to the turbo from filters. The picture in catalogue/website is Racing Chamber and Racing Suction Kit together.

Cheers

Marty

Yes but if you read the japanese commentary it says that the racing chamber kit DOES include all those pipes

Martin HKS Enthusiast

Martin HKS

Posted
Posted
Yes but if you read the japanese commentary it says that the racing chamber kit DOES include all those pipes

I can only tell you what's in the kits when I sell them and they don't include the intake pipes. Sorry.

Cheers

Marty

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • pacman_1219
      Blue/grey smoke after idle

      By pacman_1219 · Posted

      Even with the piston at TDC there was room for it to drop, but I don't think it can drop fully into the cylinder, the problem you have is that you need something pushing against the valve to hold it up so you have enough room to put the new stem seal on and the spring etc.  I used compressed air only because putting rope in the cylinder seemed a bit risky to me, I know people have done it countless times before like this. Overall it's a pain in the ass job. Honestly you'd probably be better off taking the head off because the risk of dropping something in the engine and the finicky-ness of it all is very stressful. If you are going to attempt it though i 10000% recommend a 36050 valve spring/keeper tool. I had both the traditional lever type and after doing 1 cylinder it was absolute pain to get those valve keepers in place, even with 2 people. That 36050 is amazing, you do have to push hard to get them in place but it works perfectly almost every time. Back to my actual issue I think my engine is just tired and old and the rings have gone bad. The comp numbers (cold, no oil) were: Cyl 1 -129psi Cyl 2 - 133psi Cyl 3 - 138psi Cyl 4 - 137psi Cyl 5 - 157psi Cyl 6 - 142psi   Cylinder 5 and 6 having the most carbon on them.
    • MBS206
      R33 Fuel Pump & Brakes after alarm swap

      By MBS206 · Posted

      Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • GTSBoy
      After market rear camber arm adjustment

      By GTSBoy · Posted

      Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
×
×
  • Create New...