Jump to content
SAU Community

Recommended Posts

its not that the tanks have to be majorly different

its that only 1 brand of tank has paid for the required R&D to be able to certify they are safe

and they charge a mint for their tanks

Just got an email from PJ (Paul) and he just ran 503 rwhp on the JEM dyno with 25 psi on a 3076 and 1.12 exhaust housing on E85 with 1600cc indy blue injectors.

He mentioned they did run up to 27.5 psi boost and made more power but were concerned for the intregity of the SR20 block as it wasn't sleeved.

376 rwks' has surely got to be a record out of a 3076 on any engine.....

He was frying 4th on the M5 :)

Mine will be getting tuned next week.

I made 348 at 19psi.23psi will be the aim next week, id like to see what 25psi makes on the RB though.

PJ also has water injection, so that would keep the air charge temps way down.

Im excited!!! :)

He was frying 4th on the M5 :)

Mine will be getting tuned next week.

I made 348 at 19psi.23psi will be the aim next week, id like to see what 25psi makes on the RB though.

PJ also has water injection, so that would keep the air charge temps way down.

Im excited!!! :)

Yes frying 4th at 160klm's.

He wasn't using the water injection in that 503hp dyno run.....insanely enough there is more power to come.

So he's found and extra 50 odd rwhp from the bigger ex housing, 1 psi more boost, upgraded fuel system, M&W CDI and retune.

He also mentioned EGT's were way down with the larger ex housing - as you would expect.

Been there done that. after a few sets of tyres you wonder what the fuss was all about in the first place.

With a 3076 tho? OK techically PJ is running a T25 flanged HKS 56 trim 3037 on a 2 litre.

Bigger turbo's on bigger engines make bigger torque so you'd kinda expect more fryability.

Edited by juggernaut1
With a 3076 tho? OK techically PJ is running a T25 flanged HKS 56 trim 3037 on a 2 litre.

Bigger turbo's on bigger engines make bigger torque so you'd kinda expect more fryability.

regardless of turbo / setup, you get over it after a while :)

regardless of turbo / setup, you get over it after a while :)

Haha....yes always modifying for that bigger "fix" once you get used to it.

I'm always fascinated how enthusiasts are raising the bar all the time - its amazing what people are screwing out of there motors these days.

However, what was awesome last year is average this year....and so on......where will it ever end. :)

Quick question people. What will 555cc injectors run out at roughly (kw) when using E85 on a gts-t?

About 340rwkw on std pressure using BSFC = 0.6(which is about what I've found).

BTW I've made just over 600rwhp on E85 using 60LB/hr(630cc/min) with 4Bar base pressure on an XR6T which confirms my BSFC calc of 0.6.

Just got an email from PJ (Paul) and he just ran 503 rwhp on the JEM dyno with 25 psi on a 3076 and 1.12 exhaust housing on E85 with 1600cc indy blue injectors.

He mentioned they did run up to 27.5 psi boost and made more power but were concerned for the intregity of the SR20 block as it wasn't sleeved.

376 rwks' has surely got to be a record out of a 3076 on any engine.....

I'm running RB25 with a .68 on a 3037 Pro S.

Standard Manifolds E85 etc etc.

post-46183-1246700127_thumb.jpg

Edited by RB25DETS2

that is some off the chart torque there champ....

must be hell of a ride...

what other supporting mods?

also at what revs is it making full boost?

Edited by allthewaytotheskyline
that is some off the chart torque there champ....

must be hell of a ride...

what other supporting mods?

Yeah mate lots of fun.

Just the normal stuff

PFC

HKS Turbz

850 Sard injectors

Blitz LM cooler

Blitz POD

Standard BOV

Z32 AFM

Nismo FPR

Bosch 044 in tank

Gizzmo EBC

oh and lots of boost :D (23psi)

where is the torque read out?

Heres a torque read out just for you GT....180or200's car in red (3582 .82) and mine in blue(3037 .68) overlayed on the same Dyno.

post-46183-1246776429_thumb.jpg

Heres a torque read out just for you GT....180or200's car in red (3582 .82) and mine in blue(3037 .68) overlayed on the same Dyno.

900nm, nice.. my car was making around 1080nm to 1180nm but it never had a aggresive tune, 500cc don't make too much difference.

Yeah mate lots of fun.

Just the normal stuff

PFC

HKS Turbz

850 Sard injectors

Blitz LM cooler

Blitz POD

Standard BOV

Z32 AFM

Nismo FPR

Bosch 044 in tank

Gizzmo EBC

oh and lots of boost ;) (23psi)

standard internals? 23psi??

what's with people running massive boost on un-opened engines?? i think hamish is like 23psi as well on his 33?? :P

The pressure from pre-ignition is far greater, since E85 doesnt have that problem should be fine! I've seen Lee's car hold 30 psi on the road on a cold night, that was radical!

Edited by 180or200

well i would presume (based upon what ive read) due to detonation and all, with e85 which dies off once it hits its top end of power instead of detonation that it would be much safer to push more boost without the knock.

although...i may just be wrong.

people still think that E85 is the ticket to more safe power. This is not the case! you are still limited to the engines internals.

it is easier and safer to make the power but if you are using standard internals or have a weak engine it will still break.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • This looks great! Awesome to have the 5 speed with an LSD in this. The Recaro's look like SR2's or SR3's. It's a shame they've been retrimmed as they would have looked sweet in their original colours. I think I'd want my agent to be a little more up front and informative too. I've never imported but I reckon it would make me a little nervous, so the more info the better.
    • Thanks for doing that Duncan! Makes you a good person in my books. We don't get kangaroos or wombats here. But we have bats and it's similar. AFAIK it's often the mums with a baby attached that get hit because they drop lower when starting from a tree. If you hit an animal, check on it. https://www.ifaw.org/au/resources/wildlife-rescue-app An app to get the closest wildlife rescue contact.
    • My dream is also to have a proper hoist, but I don't think it will ever happen. My quickjack is probably as close as I'll ever get, it really is very good though. 
    • Yeah we keep on in the dailies, it is pretty poor how many animals get hit and the driver leaves without checking....have saved a couple of little ones over the years. Bit of a gruesome job though, pouches generally need to be cut open because they are so tight and often the joey doesn't realise mum is gone so they are still locked onto the teat. I checked the modules in front of the DS wheel where an oil cooler should go.... There is the radar unit - that can go for race use) One of the 2 HX water pumps, the silver cylinder. That needs to be kept but might be able to be relocated But the bad news, the big computer mounted vertically in front of the wheel (blocking any potential air exit) is the electric steering computer. That is required until/unless i do a hydraulic steering conversion, and in CAD based modern car design it is not like I can just pop a big unit like that somewhere else (plus the loom would be too short anywhere else too). So, the passenger side is OK to clear out (just use a smaller washer reservoir, potentially elsewhere), but the DS no beuno
    • Well, all the best with the new camry It was interesting to hear about the UK process, it is generally a lot more streamlined here with a shipping agent looking after all the import side (noting the exact final price can still be a surprise.....) and I've used a few different brokers on the japan (or US) side, and never had any trouble with any of them....luck of the draw I guess. You mentioned you didn't get the auction sheet (understandable since you bought it from a dealer, not auction), but I always try and get hold of that because they are pretty thorough. I've imported 2x R grade vehicles over the years and both were fine, repairs in Japan are pretty thorough compared to here in Oz.
×
×
  • Create New...