Jump to content
SAU Community

Recommended Posts

Hi guys,

I recently discovered that my stock injectors are leaking a little, and i want to go to Sanddown raceway for the first time and am really keen!

Is this a risk to go down with them leaking? could they catch fire?

Opinions needed... thanks guys.

Doesn't take much heat to ignite fuel, pushing the car to its limit might make the leak larger and fuel being high pressure won't take much to squirt around the engine bay a bit. Seriously it aint worth the risk.

okay that's what i thought.. damn.

I'm surprised though because the injectors are on the intake plenum how would they ignite on the 'hotter' other side of the engine?

The don't ignite on that side. The injectors can blow out which means you won't be just weaping or slow leaking, it will pour out with force. It then runs very quickly down to the bottom of the engine, onto the sump and back towards the gearbox. From this point it can go two ways, one way leads to hot exhaust. 50% chance of it going that way, even better chance it will catch on fire.

Why don't you just replace them?

bugger.

All good though i will just have to wait until i buy my bigger turbos, i already have all the other stuff lying around at home but dont want to have to pay for tuning twice!

I guess its just more incentive to buy those turbos quicker.

I have 6 stock injectors sitting under the house doing nothing if you wanna make an offer...

i wouldn't risk it, i had a small leak in my new system (fitting not seated properly) when i primed it, it covered my engine bay in about 2 seconds.

if it got any bigger your leak will be dangerous...

bugger.

All good though i will just have to wait until i buy my bigger turbos, i already have all the other stuff lying around at home but dont want to have to pay for tuning twice!

I guess its just more incentive to buy those turbos quicker.

take the injectors out and run them to a local shop to replace the orings on the tips, usually stops most the leaks from memory

I depends you cant tell till you pull them out for sure though.

That may be the case. Pull them out and have them checked. You will know for absolute certain then.

Usually all you need to do is spray some carby clean around to clean the area then have someone start the car. while you watch the small hole in the side of the injector.

If it's the top seal, it will leak before the car is started. If it's the injector it'll leak once it starts. The bottom oring will only leak air, not fuel.

hey i would take AXE S up on his offer.. just replace the injectors.. you can then still go track.

correct me if im wrong but driving a car at all either track or street with a leaking injector cant be good at all IMO..

I would sort this out asap.

Just my 2c

you should not be driving it at all really. get it fixed. stock injectors are cheap to source. get them cleaned and flow tested too, new o-rings and whack them in. then away you go.

yes take it to the track! get all your mates to bring video camera's.. be sure to carry a fire ext and make sure you upload the fire to youtube.

+1...

Don't know how I missed this one............. :)

Oh you did forget to mention...if you admit you had leaky injectors and drove the car...insurance won't pay.

i just had the same problem put in the sard 720s

with the pfc all my tuner had to do was load my map up, type in what inj they were and a few other numbers.... theres my old map with the new map for the 720s ready to go load it on... couple power runs to check all the air fuels perfect!!!

10min job cost me 150bucks and thats with putting the new inj in and all!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • haha don't worry I'm sue you've got more fun ahead buying a 30 year old turbo car....but at least you are in the right place to ask
    • some days eh? The keyless entry and interior light on/off with the key will be controlled by the Body Control Module, but I'm not certain where that is or what it looks like (you might get lucky with a search to get a part#, which could be printed on it). I'd start at the A pillar/ Under dash/kick panel on the driver's side
    • It might be hit and miss, but Nissan Genuine Parts and Pitworks are not the same thing, although both are available from Nissan Dealers with Nissan Part Numbers. Nissan Genuine Parts are the OEM stuff, Pitworks are their attempt to get people back from generic parts makers
    • I did end up getting it sorted, as GTSBoy said, there was a corroded connection and wire that needed to be replaced. I ended up taking out the light assembly, giving everything a good clean and re-soldered the old joints, and it came out good.
    • Wow, thanks for your help guys 🙏. I really appreciate it. Thanks @Rezz, if i fail finding any new or used, full or partial set of original Stage carpets i will come back to you for sure 😉 Explenation is right there, i just missed it 🤦‍♂️. Thanks for pointing out. @soviet_merlin in the meantime, I received a reply from nengun, and i quote: "Thanks for your message and interest in Nengun. KG4900 is for the full set of floor mats, while KG4911 is only the Driver's Floor Mat. FR, RH means Front Right Hand Side. All the Full Set options are now discontinued. However, the Driver's Floor Mat options are still available according to the latest information available to us. We do not know what the differences would be, but if you only want the one mat, we can certainly see what we can find out for you". Interesting. It seems they still have some "new old stock" that Duncan mentioned 🤔. I wonder if they can provide any photos......And i also just realized that amayama have G4900 sets. I'm tempted too. 
×
×
  • Create New...