Jump to content
SAU Community

Recommended Posts

Hey guys

I was filling up my car to full today and i realised beneath me there was petrol. I looked under my car and it was leaking fuel by the time i filled up i would lost an easy litre and there is a smell of petrol fumes which my mechanic had stated it was coming from the boot where the fuel tank is. At the moment i get approx 250 km per full tank but at first i thought it was linked to my transmission not kicking into overdrive when driving at 100km. what is wrong with my car?????

pls help

thanks in advance

Does your car have an aftermarket fuel pump? It may be that the O-ring that seals the fuel pump panel is perished or mis-aligned.

Check the restrictor neck (where you fill) has been installed correctly. It should be "sandwiched" between the body and the fitting that takes the fuel cap.

Thanks for your help guys

No it is not leaking from the boot it was leaking underneath the car. I also checked the boot when i saw it leaking and it wasnt leaking from the boot next to the battery. I drove home and checked if it was leaking but it stopped.

Also, the guy i had bought the car from had an aftermarket fuel tank or surge tank or whatever it is but he removed it from the car so i was thinking he didnt remove it correctly thats y it is leaking?

are you sure it wasn't just the little overflow from being overfilledd? the filler neck has an overflow thing in it and this dumps the fuel out under the car.

Beer baron yea but even if he did over fill he shouldn't be getting 250 per tank thats shocking, I get 300 and I know somethings wrong, replacing the O2 sensor hopefully it's that

Detour do you notice fuel on the ground when you park? or less fuel in your tank *keep in mind the fuel gauge reading is altered by the temp outside and the engine*

Hi,

I had a similar problem. It turned out that the seal on top of the fuel tank was leaking, but only when you the tank was filled to the full mark. A small amount would leak over the top of the tank down the sides and then directly underneath the car.

Remove the inspection plate located in the boot. This will reveal the access to the top of the tank and fuel pump. Go to your local servo and fill up your tank till it's full. Keep an eye out on the top of the tank and if you notice fuel pouring out of the top (trust me you will notice it) then its a good chance that it's the seal. It would also be a good idea to check all the fuel hoses going to and from the tank and check for wear or cracks.

Hope this helps

Regards

Hey guys

I was filling up my car to full today and i realised beneath me there was petrol. I looked under my car and it was leaking fuel by the time i filled up i would lost an easy litre and there is a smell of petrol fumes which my mechanic had stated it was coming from the boot where the fuel tank is. At the moment i get approx 250 km per full tank but at first i thought it was linked to my transmission not kicking into overdrive when driving at 100km. what is wrong with my car?????

pls help

thanks in advance

can i ask does the rear of ur car always have a fuel sorta smell.. cause im having a similar problem.. when i fill it up it overflows.. and it always a fuel sorta smell to the rear of the car n also get terrible fuel mileage.. usually around 250kms/tank

anyway im going to have a look at some of the suggestions tomorrow and see if i can fix the problem

I had a similiar problem on my R33. It was the hose coming from the fuel pump to the connector under the car. It was split in the middle, so the only way I picked it up was by having someone look in the access panel in the boot with a torch, and then I was turning on the ignition to prime the fuel pump. Because it was wet under the car while it was off, but you could only see the leak when the car was on.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • (it is a brand new ported mellings pump) I suspect the lack of pressure is due to the leak. It was *not* that low in other logs of oil pressure in the past. It wasn't that hot either, but not far off.
    • Would a Mellings oil pump be a viable option  From my time with a LS, and talking to tuners and LS specialists, the "weak" OEM oil pump is one of the first things they recommend to swap out if I was going to give the engine any high RPM I opted for a Mellings high volume, with the high pressure springs and I never had a issue with it Cost wise they are not expensive in the scheme of things 
    • Just bought a 2002 Stagea 250tRS VR-X Four AERO VQ25DET and spent the last two weekends cleaning and detailing it.. still have to do the wheels and the engine bay but the rest of it came up nice. Imported 2011 to S.A. and I'm the third owner since it was imported. I met the guy who brought it over, he went to Japan and picked out the car, bought it and ordered the wheels. He also gave me a list of stuff he did to the car with receipts. Coil overs (I have the original springs), 3" exhaust from the dump pipe back no cat, Custom dump pipe,(I have the original exhaust), Plenum spacer, 18" custom Work XSA wheels (need restoring, I've made a start..), Shift kit put through the 5 speed tiptronic auto, TV and menus/screens changed to english, Australian DTV tuner installed in rear. I've just had four new discs and new pads as well as all the fluids including the brake fluid replaced. I have all the receipts for the last 15 years and the import papers in a nice folder. Car looks great, goes like hell but fuel economy is not a thing lol.. pics next..
    • I ended up in this rut again lol, and used a shit ton of filler. One thing I can't understand is, even after using a big long block and going in long X pattern strokes, I always end up at bare metal again with no filler, and my repair started at one end of the door and now I've chased my tail to almost the other end of the door. I was thinking of hitting the panel with a hammer where it might be a high spot and making everything low then filling it, I did this on a small section on my other door by mistake and I think I fixed it lol. Is this a bad idea? The other thing is with guidecoat, whether it's the powder or spray, after I sand all the guide coat off, it doesn't reveal anything for me in terms of high spots and low spots and makes it especially hard when it's bare metal (at least in powdered form), am I doing something wrong here, or likely a high spot I keep going over and creating valleys? Lastly, stupid question but, is it possible that after sanding if I only sand over the filler area where I know to be a dent that it's impossible for me to dig into that dent? Unless there are other problems which I missed.  
×
×
  • Create New...