Jump to content
SAU Community

Jjr Intake Manifold Rb25det

CeJay

By CeJay,
in Engines & Forced Induction

 Share

Recommended Posts

H@ME Mentor

H@ME

Posted
Posted

yeah there is a topic on how to install them in the D.I.Y section i used it when installing mine comes up a treat if you wanna see photo's look in here (forced induction section) for my topic Green N/A build.

Bliksem Veteran

Bliksem

Posted
Posted (edited)

Cheap copy of Greddy. Some people have them though. I think its a bit of a gamble whether or not you end up with one thats cast properly or not... in saying that just jap would probably replace it for you. I went with a proper Greddy on my car, I personally prefer to support the genuine stuff.

Edited by MintR33
MANWHORE Grand Master

MANWHORE

Posted
Posted

A few years ago, Greddy was the only feasible aftermarket plenum option for the rb25.

Then suddenly someone copied it and flogged them off cheap.

I have no experience with this particular jjr product and as such I am not commenting on that product, but some people have noticed flow inconsistencies between the cylinders with the copies I referred to.

guricha Collaborator

guricha

Posted
Posted (edited)

i had this manifold instaled on my previus R33 and efect was great, manual was here in DIY section but i cant find it there any more:(

here is the link:)

http://www.skylinesaustralia.com/forums/to...l&hl=plenum

Edited by guricha
  • 2 months later...
W0rp3D Grand Master

W0rp3D

Posted
Posted

Unless you are in a huge hurry to get one i would keep an eye on ebay and the for sale section and wait for a genuine greddy to pop up, will cost you a few hundred more but will work the way it should.

copying the out side of one of these is easy, the inside is where all the r&d goes and thats the dodgy bit of these copies.

  • 2 weeks later...
TiTAN Grand Master

TiTAN

Posted
Posted
It usually has a big GREDDY logo in red stamped on the top of it near the throttle body :)

my genuine Greddy one didn't have a red logo stamped on it. it did however come with a Greddy sticker that goes in the big raised up rectangle on top of the thing. it also comes with shiny screw in fittings for the the vacuum/pressure lines and pretty much all the vacuum hose / clamps / bolts etc you need to install the thing.

Mr. Untouchable Experienced

Mr. Untouchable

Posted
Posted

mmm ive seen a few of the ebay copies first hand. they are pretty average.

I'm going to buy one soon and cut it open, weld the pin holes/craters and shitty bits up and clean the runners up and then weld it back together. then get the surfaces machined and maybe putty and paint one. see what the total comes to.. just for science

as they come tho they are pretty average. genuine greddy items are very pricey now. and hypertune are great and are also expsensive..(but when you know what goes into them, ie runners, velocity stacks and the billet plenum section they are a work of art and are worth every damn penny. plazaman items also look the biz. high quality stuff and results to back it up

i bought a stryder manifold (very simular design to hypertune). couldnt be more impressed. but i had to modify a few things. had to fit throttle cable bracket. and move both water sensors near the top radiator pipe inlet..... bit of mucking about but great product

anyway as for the chinese copies mate they are like any other chinese product. Hit and miss buyer beware

cheers

Marco-R34GTT Grand Master

Marco-R34GTT

Posted
Posted

I wonder if anyone has tried a NISMO one, from what I understand the NISMO one is the unit that MINE's uses when it replaces the plenum on it's stage 2 RB26 upgrade.. I wonder if they can be made to fit an RB25 liket he Greddy one can???

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Piggaz
      R32 gtr transmission strength, billet plate

      By Piggaz · Posted

      You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • The Bogan
      NC MX5

      By The Bogan · Posted

      So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
×
×
  • Create New...