Jump to content
SAU Community

Had Enough...

Sammy34

By Sammy34,
in Queensland

 Share

Recommended Posts

Sammy34 Community Regular

Sammy34

Posted
Posted

So when I got my car brakes were squeeling. Since then I have had,

1. front brake pads replaced to a non metal compound (still squeeling)

2. so then the brake discs machined (stopped squeeling but now the rears have started)

3. was told the rears needed to be machined as well (so got them machined and there still squeeling)

4. then was told i need to get rid of the metal compound brake pad on the back (removed an still squeeling)

in amoungst all of that I have had a brake caliper fall off why I was driving because the mechanic didnt tighten the bolts back up on it, the car is pulling left when I brake.

Tyre Zone capalaba have made a few stupid mistakes, they have attempted to put there best foot forward and correct any mistakes that have been made and I can respect that. But the quality of work is poor and I wouldnt recomend anyone living in the capalaba area to trust them with your vehicle.

But that is beside the point of why I posted. What should my next step be? Id rather not hafto go get a whole new brake setup with slotted rotors etc... but if thats what I hafto do to stop the problems with my car then I guess I will jsut go get it done. As for the car pulling left, I hope its just bad wheel alignment, but nothing would surpise me now.

Link to comment
https://www.sau.com.au/forums/topic/244780-had-enough/
Share on other sites
666DAN Grand Master

666DAN

Posted
Posted

A few things may be causing that, I'd get the brake system re-bled just to make sure there is no air causing brake pressure variation.

Check the tie-rod boot, make sure none are burst. Check the sway bar make sure no bushes have split, and the bolts are done up nice and tight.

All types of pad I've had on my car have squeeled a bit I'm afraid.

Should have bought my car :yucky: (jokes)

Link to comment
https://www.sau.com.au/forums/topic/244780-had-enough/#findComment-4260315
Share on other sites
666DAN Grand Master

666DAN

Posted
Posted

What a bunch of clowns.

Oh and if by some twist of fate, I just drove my car and the only time I can get a squeal is literally just as the car is coming to a halt...seems all my squeal has gone to your car?

Also weird I just got pulled over for an RBT....10am on a School day, I'm not that keen :yucky:

Link to comment
https://www.sau.com.au/forums/topic/244780-had-enough/#findComment-4260400
Share on other sites
Sammy34 Community Regular

Sammy34

Posted
  • Author
Posted
What a bunch of clowns.

Oh and if by some twist of fate, I just drove my car and the only time I can get a squeal is literally just as the car is coming to a halt...seems all my squeal has gone to your car?

Also weird I just got pulled over for an RBT....10am on a School day, I'm not that keen :P

Yeh mine squeel when im moving slowly... but its not those little chirps u can get from new brake pads i mean its a screeching sound. RBT on a Friday Morning! whats the world coming too?

Link to comment
https://www.sau.com.au/forums/topic/244780-had-enough/#findComment-4260512
Share on other sites
R334door Experienced

R334door

Posted
Posted
So when I got my car brakes were squeeling. Since then I have had,

1. front brake pads replaced to a non metal compound (still squeeling)

2. so then the brake discs machined (stopped squeeling but now the rears have started)

3. was told the rears needed to be machined as well (so got them machined and there still squeeling)

4. then was told i need to get rid of the metal compound brake pad on the back (removed an still squeeling)

in amoungst all of that I have had a brake caliper fall off why I was driving because the mechanic didnt tighten the bolts back up on it, the car is pulling left when I brake.

Tyre Zone capalaba have made a few stupid mistakes, they have attempted to put there best foot forward and correct any mistakes that have been made and I can respect that. But the quality of work is poor and I wouldnt recomend anyone living in the capalaba area to trust them with your vehicle.

But that is beside the point of why I posted. What should my next step be? Id rather not hafto go get a whole new brake setup with slotted rotors etc... but if thats what I hafto do to stop the problems with my car then I guess I will jsut go get it done. As for the car pulling left, I hope its just bad wheel alignment, but nothing would surpise me now.

If the car is pulling to one side, you may have a kinked brake line when the caliper came off causing the opposite caliper do the work and the other side nothing having no fluid pressure to it.

If so charge that to the guy who forgot to put it on properly for a new brake line,only if thats the case.

Not all brakes squeel, pads yes have something to do with it, but also make sure the fitter has installed the brake pads properly as the metal shims in the caliper may be touching your disc causing it to squeal when you brake.

Hope this helps.

ALso even though you are in brisbane i would reconmend Marty at mw performance it you need any work done ,he is on the sunshine coast , maroochydore though, he did all my brake work and its top notch.

Link to comment
https://www.sau.com.au/forums/topic/244780-had-enough/#findComment-4261248
Share on other sites
dangerous_daveo Grand Master

dangerous_daveo

Posted
Posted

If they are as dodgy as you say...

I'd be checking the pads are bedded in correctly. They have put on backing plates and wear indicators correctly. Id also check that your brake disk stone shelds aren't bent and rubbing on the disk etc.

Also as above check out all the other stuff.

Link to comment
https://www.sau.com.au/forums/topic/244780-had-enough/#findComment-4261474
Share on other sites
R34GTX Rising Star

R34GTX

Posted
Posted

Simple answer, do your own brakes. Not hard to do at all. I fitted new rotors (DBA 4000 slotted and Hawk HP Plus pads) front and rear, brake bleed and

also dust boots on pistons (which required a semi rebuild of the calipers). All in all took me about half a day. The pistons can be a little tough to pull out, but if you have an air compressor you can get them out pretty easily.

You're car might be pulling to one side with braking if your dust boots over the piston have disintegrated and now you have scoring on your pistons. If this is the case, it is definately time for a brake rebuild.

As for squealing, I used to have squealing with new pads until they were bedded in or until I did my first track day, but after that they are sweet. I also beleive that slotted rotors help clean the brake dust away more efficiently from the rotor face than stock rotors. Might be worth a look as DBA's are getting cheaper and cheaper everyday, plus you also get a performance upgrade for little $$ outlay.

Link to comment
https://www.sau.com.au/forums/topic/244780-had-enough/#findComment-4267820
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      Torana Lx Gtr Hatch, Lots Of Pictures

      By The Bogan · Posted

      LOL, when one "money pit" is never enough Noice, and excellent work mate
    • The Bogan
      NC MX5

      By The Bogan · Posted

      I have more than enough digging, laying blocks, moving gravel, airrating, feeding and top soiling the grass, and setting up the veggie gardens growing some seedlings,  and then removing all the unused rock to keep me busy for the next few months at least,  hopefully the rain stops soon so I can get a few hours in this arvo, but, before that Sunday is washing day, is every body happy, you bet your life we are Nice country road day drives are a day off whenever I'm muscle sore from all the landscaping at the moment, but, more epic multiple day drives will start once the majority of the big jobs outside are completed
    • MBS206
      NC MX5

      By MBS206 · Posted

      I hear that would involve some nice country road drives into the hills for Mark...
    • MBS206
      Recommendation for engine oil funnel spill free

      By MBS206 · Posted

      I thought I'd come back and add something I JUST learned. A Toyota LandCruiser with a 1HZ, mates perfectly with a bottle of Nulon brake fluid. As in, it perfectly screws in. Great make shift funnel when you cut the bottom of it off. This may work for your Corolla.   Unfortunately, tipping a 10L drum is much harder than a 4 to 6L bottle, and they no longer include the easy pour tap which was just perfection to use previously.  
    • EndZee
      Fuel Pump Control Module & Dropping Resistor

      By EndZee · Posted

      Guys since i bought r33 gts25t coupe 1994 automatic a/t(manual swap 350z gearbox)  all i got is problems, always problems. Lets start with that when i turn key into ignition(ON) fuel pump doesnt always works. Sometimes i have to turn key twice Off/on/off/on until it primes. Its new, dw300 - 340lph. My gearbox broke so i did gearbox swap, install different intake manifold, injectors and i take pipes. Car was sitting in garage for more than half a year. I did assembly all not that long ago and when i turn ignition cant hear prime. All of sudden it stopped working. Theres many videos on YouTube how to make relay mod on r33 straight from battery so i did and it doesnt work! 😰 30 - battery positive  87 - positive from fuel pump to relay 85, 86 - one of two wires from original fuel pump wires(light blue, grey) and it didn’t work. so I check on ignition and took original BLUE relays wires from trunk, next to fuses. (I believe it’s IGN+ and ECU pin 18. it didn’t work…  tried connecting (IGN+ from og relay) and (ECU 104 from 1of4 FPCM wires) to my new relay 85/86 and it didn’t work.  I unplug FPCM. Didn’t work. im thinking what’s wrong   fuel pump is working, if I leave IGN+ on 85 and 86 straight to ground it works but it’s just nonstop. Since it getting constant 12v after key in ON. light blue wire gives me 6-8v.  so how this should be connected? What causing ECU not giving — on pin? Or I did sth wrong and that’s why it doesn’t work? I need negative signal on ECU that control fuel pump. What this should be?
×
×
  • Create New...