Jump to content
SAU Community

At Wat Power Level Do U Start Running Into Problems With The Standard Rb26 Fuel Rail

STR8E180

By STR8E180,
in Engines & Forced Induction

 Share

Recommended Posts

STR8E180 Proficient

STR8E180

Posted
Posted

i had my car on the dyno for a tune yesterday and when we got to 400kw it started running into problems with fuel

we had a fuel pressure + flow gauge connect to the car while we were tuning the flow doesnt drop at all but the fuel pressure goes from 40psi to 60psi and then just drops back down to 40 instead of going higher it just drops back to 40 and the car leans out so we neva got to finish the tuning

fuel system is pretty basic

bosch 023 (rated at 700hp) mounted intake

SARD 800cc injectors

HKS fuel reg

Beer Baron Grand Master

Beer Baron

Posted
Posted

well pressure dropping is usually an indictor of pump running out of puff, or faulty fuel regulator, not restrictive fuel rail. are you sure the fuel flow wasn't affected at all by pressure change? where were you measuring the flow, and how?

STR8E180 Proficient

STR8E180

Posted
  • Author
Posted
dirty fuel filter?

its got a brand new fuel filter already on it

well pressure dropping is usually an indictor of pump running out of puff, or faulty fuel regulator, not restrictive fuel rail. are you sure the fuel flow wasn't affected at all by pressure change? where were you measuring the flow, and how?

it cant be a fuel reg because at 1st we thought it was a faulty fuel reg and replaced my SARD fuel reg with a HKS one and it changed nothing

the fuel gauge we have is the blue one

the gauge is used to measure fuel pressure the it has a ball which moves up and down to show u how much fuel flow u have

isnt the 023 rated less then a 044?

could be upgrade time

the 044 is rated at 600hp

the 023 is rated at 700hp

if you are running stock wiring to your fuel pump then that will be part of your issue kemp

we have already wired the fuel pump so it gets full voltage

TiTAN Grand Master

TiTAN

Posted
Posted

are you sure the 023 is rated higher than a 044? From what info i could find the 023 is rated at 163L/H @ 5bar vs. the 044 rated at 200L/H @ 5bar.

The HP ratings on pumps vary by 300hp depending on where you buy them, the L/H don't.

Piggaz Grand Master

Piggaz

Posted
Posted
Who has actually found the limits of the stock fuel rail?

I know its not the answer to your question but i had just on 400 KW at the treads on a stock rail and Nismo regulator.

N1GTR Grand Master

N1GTR

Posted
Posted
I know its not the answer to your question but i had just on 400 KW at the treads on a stock rail and Nismo regulator.

Cool thanks

Would be good to know at what point it gives up for future reference and anyone doing a search will no doubt read this thread and hope to find the answer

dangerman4 Mentor

dangerman4

Posted
Posted

at 400 rwkws i would be starting to think about 2 044 to give you some room to play.

as i mentioned earlier 1 x 023 would be simply running out of legs.

STR8E180 Proficient

STR8E180

Posted
  • Author
Posted
Why?

I run a surge/external in mine and i drive it daily. I cant say its that much louder at all if the pump is mounted decently

i realli dont want to go threw all the trouble of fitting a surge tank and all the lines im after some thing i can just bolt in and fit the problem

i wanna get out of this the most cheapest way i can as well

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Ok thanks..that was my second question if i can somehow bypass this even with Nistune(that is all i have right now...aparat from stock ECU. So with some aftemarket it can by "bypassed" or make it work?  I know there is Link or Haltech (mainly used). We have ECUmaster here so i will gather some info about it.
    • GTSBoy
      Boost cut after swap(RB25DET NEO) R34

      By GTSBoy · Posted

      Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Ok so ABS/TCS is "not" the problem. Yeah i know now about the ABS with Nistune(i told that to the Nistune guy) but iam not 100% why or why i dont have ABS. ABS cube is in the engine (always has been) but i had braked couple of times rly hard and brakes just locked and scream. Does all Skylines have ABS cube? That boost sensor https://www.sau.com.au/forums/topic/367633-wtb-r34-gtt-turbo-pressure-sensor-pics-inside/ Is this it? I need to ask but i have a picture of engine bay and i do not see that (100% is not in that place) If i do not have this the car can do what mine is?(cutting around 4000 rpm) Here is the pic of my engine bay(only one i have) BUT i think i dont have that cuz loom was used from my RB20DE NEO and i know (obviously) that it does not have boost control or any wire to that...) so maybe that is the problem? (i dont know for 100% if that car where the engine is from had that)...but i dont have the loom from that
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Duncan
      S1 rb25/s14 starting problem

      By Duncan · Posted

      Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
×
×
  • Create New...