Jump to content
SAU Community

Recommended Posts

Alright, this will be my next projec tonce I get my S15 RB26DETT up and running but as for now I am already acquiring some parts, namely the damaged RB26DETT engine. I have done a bit of searching and people are saying that you need to machine the headstud holes and retap, some others also said you can use the RB25DE headstuds and they work proper, can someone clarify. What else needs to be done, was thinking about a new headgasket and a baffle and the usual RB26 headwork for oiling problems. Can anyone advise me who has done it as I am thinking along this direction. If the damaged engine has a good block and crank then my swap will be an RB26 but not sure until it is scrapped, guy just told me it was a spun bearing and the crank needs polishing but no one can know unless it is scrapped. Let me know what is needed as I am thinking along these lines.

Good question that , non VVT head on VVT block - if the 26 block is RS .

I suppose you could look for an R32 RB25DE block and fit it with piston oil squirters and good internals .

I think American mobs can sell you non metric threaded fasteners but you have to get the block drilled/threaded and not sure about the heads bolt holes .

Ask SK , cheers A .

  • 3 weeks later...

What exactly do you want to know? The head will bolt on using rb25 head bolts, but as i said the compression ratio will be low due to the difference in cylinder volume. You really aren't gaining anything by using a neo bottom end, as a non-neo bottom end will end up with a more appropriate comp ratio. You could get a set of non-neo forged pistons and fit them to the neo bottom end, that will fix the comp issue.

Okay are you sure that using the RB25 headbolts I can bolt on the head? The reason I am using the Neo bottom end is because the RB26 engine that I am getting has bottom end damage and that I already have an RB25DET Neo engine in my GTT. Maybe the RB25 forged pistons may be an option I can look at, thanks. I just want to confirm that the headstuds from the RB25 can work on the RB26 head without worries, can you confirm firsthand?

I wanted the individual throttles and also the intake mani run on the side for shorter coldside piping, and also maybe do a twin turbo setup all at the same time, oh and the wow factor :/. Actually I am getting the RB26 for a good price and getting aftermarket intake manis for the RB25DET Neo is harder and expensive along with the harder to get injectors and then the exhaust manifold. Okay so RB25DE or is it RB25DET headstuds or are they the same, gonna do a search now?

Yes I know but I am getting the entire head for a good price and having the individual throttles is an added bonus as well as the twin turbo setup. Let's not harp on the topic I just want to make sure you can use RB25 headstuds and if so is the RB25DE and DET headstuds the same, I am thinking so. Thanks to all for the input BTW.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
    • Heh. I copied the link to the video direct, instead of the thread I mentioned. But the video is the main value content anyway. Otherwise, yes, in Europe, surely you'd be expected to buy local. Being whichever flavour of Michelin, Continental or Pirelli suits your usage model.
×
×
  • Create New...