Jump to content
SAU Community

Recommended Posts

Hey guys

some of you saw my car at the meetup, just posting a few pics of the new rims on the car

19 x 9.5 +17 - 265/30/19 Dunlop SP Sport Maxx

19 x 10.5 +17 - 295/30/19 Michelin Pilot Sport 2

imo the right size 19" rim doesnt actually look small on the v35.

i also have Nagisa Auto Rear Camber, Rear Toe, and Front Camber arms in order to make the rims fit.

Running -2.5 Degrees Camber all round.

I also installed some HKS Kansai sway bars too. They make a MASSIVE difference to the body roll and handling of the car. A must have first mod for Everyone!

Car has been lowered, it is sitting on TEIN Comfort Sport Coilovers. I think they are at the max it can go in terms of height adjustment. This made the biggest difference to the look of the car, as a low V35 looks AWESOME!

one thing i planned for, is that i currently have 10mm hubcentric slip on spacers on order, so that i can bring the front rims out, bringing the offset of the front to +7. I would of ordered them in +7, but RAYS dont make them in that offset. Its +17 then +4...... big jump.

only 2 pics i have. enjoy.

-mark

GTS1.JPG

GTS2.JPG

Edited by BLISTC
Link to comment
https://www.sau.com.au/forums/topic/247485-new-shoes/
Share on other sites

Is -2.5 degree a bit too much for daily driving ? I had my R33 previously set to around this, as I took it to track once in a while, and it wears out the inside half of the tyres real fast... as it's driven more on the street basically daily.

Link to comment
https://www.sau.com.au/forums/topic/247485-new-shoes/#findComment-4298239
Share on other sites

hey guys thanks for the replies.

ive seen some V35's with 20" and in some photos it just looks too big. i reckon the best fitment would be 20" Rear and 19" front but then i dont know what that would look like.

-2.5 degree camber is alot, but all i do is going to get the tyres swapped around every 10,000kms or so, so that they will wear a bit more evenly. making the car look good comes at a price unfortunately.

PS. i also had to roll the rear guards as well to get that offset rim under the car

Edited by BLISTC
Link to comment
https://www.sau.com.au/forums/topic/247485-new-shoes/#findComment-4298638
Share on other sites

Good work, looks nice and I hope you don't forget to switch the tyres with the Camber your running...

some people forget unfortunately wasting tyres early in the piece.

nah i wont forget

its something i always keep an eye on and do and have done with my last 2 cars also

Link to comment
https://www.sau.com.au/forums/topic/247485-new-shoes/#findComment-4300623
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
×
×
  • Create New...