Jump to content
SAU Community

Recommended Posts

What do you guys think is better a 970 black edition or a 970 wind force ?

Apart from clockspeeds (usually isn't much to be honest) and the styling they will be the same. There isn't really much that distances the same cards today. They are both good so get whichever is the best deal.

  • 3 weeks later...

I will probably only have windows on the ssd and what is a good price for a 3.5 ghz i5?

Not sure but you could always look on eBay and see what kind of deal you can get. If you're in the UK you could look on Scan.co.uk which is a pretty decent site, I've got quite a few components off there and so far no issues with them.

eBay you can get decent parts if you're willing to look around. I've just bought an old EVGA GeForce GTX 460 SuperClock which cost £40 + £5 for delivery, I didn't need it but I like them so it was an impulse purchase.

My R9 280X with 3gb of DDR5 has been doing very well with modern games lately.

Few hiccups with GTA5 due to AMD, but runs 50-90fps on high-ultra settings (all the advanced graphics and distances turned off). And been running really well with project cars, maxing out everything except shadows and reflections (to keep it smooth). Also none of the issues that the 290 cards are having

My R9 280X with 3gb of DDR5 has been doing very well with modern games lately.

Few hiccups with GTA5 due to AMD, but runs 50-90fps on high-ultra settings (all the advanced graphics and distances turned off). And been running really well with project cars, maxing out everything except shadows and reflections (to keep it smooth). Also none of the issues that the 290 cards are having

Have the same card, also surprised how well it plays modern games.

Case: NZXT H440
Motherboard: Gigabyte GA-Z97-D3M
CPU & CPU Cooler: Intel i7 4790K & Corsair H100 GTX
RAM:Kingston Hyper X 8GB 1866Mhz Dual Channel
Monitor: 25inch Dell Full HD Monitor (will upgrade soon)
Graphics Card: Gainward GeForce GTX980 4GB GDDR5
HDD(s):Kingston Hyper X Fury 120GB SSD & WD Green 1TB
OS Used: Windows 8.1
Peripherals: Razor Orachi Wired/Wireless Gaming Mouse, Logitech G27, Xbox One Controller

  • 4 weeks later...

Just started to collect parts for a new build, my 5 year old PC is starting to show its age.

Starting off with a Mini ITX and a Lian Li.

I have the case, but i'm waiting for all the new lineup of GPU's to be released.

  • 2 weeks later...

How do you guys get neat cable managements?

My case looks like a rats nest inside with explosions of cables everywhere, and my poor attempt at cable managements only made the inside 1000xs worse... :closedeyes:

Be gentle with the Corsair cooler. Also that WD Green drive, if you're doing anything more than archiving, you're gonna have a bad time.

Corsair is holding up really good at the moment as i have overclocked it to 4.2Ghz without any dramas. I will order WD Black 1TB drives, agreed the Green will cause trouble other than mass storage as its limited to 5200rpm versus the 7200rpm of Blue and Black.

Corsair 450D:
Gigabyte Z97X-SOC:
i7-4790K+H100i:
Corsair Vengeance Pro 2133 (4GBx2):
Acer 24":
Gigabyte GTX 770 2GB:
840 EVO 240GB, Seagate 4TB(s):
Windows 8.1 + OS X 10.8.2:
M65, K40, NZXT Hue:

It's overkill for the games that I play.

Corsair is holding up really good at the moment as i have overclocked it to 4.2Ghz without any dramas. I will order WD Black 1TB drives, agreed the Green will cause trouble other than mass storage as its limited to 5200rpm versus the 7200rpm of Blue and Black.

The WD greens are nice and quiet though. But horribly slow.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...