Jump to content
SAU Community

Recommended Posts

It works quite well apparently. Yet to try it on my R33 though, next on the list.. My lights aint heaps bad though just a about half the RHS light.

I found the best for my headlights has been to use one of these kits first off, and get the lights very clear. Then once every few months they will get a bit dull again, just go over them with some cut and polish and bam good as new.

  • 5 months later...
  • 1 year later...
  • 1 month later...
  • 4 weeks later...

I just applied some cut&polish to my very smokey yellow headlights yesterday. Made sure I rubbed it in nicely, then moved over to the other headlight, waited 5-10 minutes for it to dry up in the sun and removed it. Lights came out glimmering!

Will post pics!

  • 3 weeks later...

I still stand by the PlasticX or whatever its called. Had another crack at mine on saturday, but did it with an electric buff instead. Saved me lots of time and energy and turned out pretty decent.

My lights arent in tip top shape, they have a bit of crazy cracking going on. hard to tell if its the inside or out. But once they have been polished up you dont notice it too much.

Hoping its obvious that the drivers side is done and not the passengers :P And try to ignore the passengers indicator. LOL. It fell out under brakes and i run the bugger over. Was all that was left of it! Dam LED Repco light replacement.

20120226_155744.jpg

Edited by gotRICE?
  • 3 weeks later...
  • 5 months later...

I use Brasso and a few rags and that seems to bring them up like new again. What i do is wash them and wait for them to dry then apply the Brasso and leave for a few minutes then with a clean rag give them a firm wipe off!

I use plastx myself and I think there are a number of solutions that will get rid of the yellow. However, I am more interested in a good sealant to make it last.

So far a coat of clear has yielded the best results and lasted a good few months - is there a longer term solution?

I am more interested in a good sealant to make it last.

This.

The Turtle Wax Kit I used above, looked the goods for a while, but I'm back to yellow.

The UV sealant provided in the kit is obviously of teh gaids.

  • 3 weeks later...

My problem is its from the inside were all the damge is not on the outside,i used plastx there already clean headlights they are xenon S3 although it looks like the problem might be from the inside of the headlights unfortunately..

  • 3 months later...

Reviews look promising. Possible group buy?

would be interested.

i used glassylite about 1 week ago, can post up pics here when im home tonight if anyone wants them. will report back in a few months to see what the progress is.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...