Jump to content
SAU Community

Recommended Posts

Hey guys,

I have owned the GTR for about 2 years now and have blow 2 lots of turbos in that time. Being a poor bastard and liking the stock power I replaced them with stock ones again. That was all fine and dandy makeing about 0.9 Bar boost all day every day. The car is completly stock engine wise. Basic support mods include HKS Intercooler, HKS Exhuast and HKS BOV. Stock ECU, Injectors ect

Now heres my problem. I have been using it as my dayly driver for abit now giving it a fairly easy life putting around in traffic. Now all of a sudden it doesn't like to boost pass 0.6 bar and blows a f**k load of smoke out the back. Missfires and doesn't go very fast. The car still revs to 7.5k, idles fine, builds boost quickly as well. Smokey ilde sometimes.

I have checked the following -

  1. Blocked BOV - Didnt notice and different
  2. Checked all pipping - intercooler hoses and fuel lines - all ok here
  3. Reset ECU - no change
  4. Checked for shity fuel with water in it. Flushed tank - still the same

Going to do a compression test this weekend will report back with what i find, the problem is i have done alot of research and it points to a leaking intercooler pipe. Checked all the piping a million times now and still nothing comes up.

I also can't take it to a machinic because i live in a small rural town full of FORDs and Holdens and the mechs scratch there heads with my car. My last resort will be chucking it in the back or a trailer and taking it to HyperDrive MS.

Cheers, :P

Link to comment
https://www.sau.com.au/forums/topic/249980-r32-gtr-with-black-smokemiss-fire/
Share on other sites

black smoke is excess fuel

checked AFM's? Mine started to occasional stall whilst on light load. needed cleaning and now all good, better + better throttle response.

Checked plugs / gaps / leads ?? with increased boost the spark can be 'blown' out with a large gap/stuffed plug as boost increases

yeh can imagine very few nissan turbos floating round in gero :P

Yep only r32 GTR in town. Makes it hard sometimes....

New spark plaugs were graped to .08? or .8? one of the two. AFM are a bitch to get to will check tomorrow.

Could it be a piston that is stuffed?

Thanks for the hints.

Dont know the gaps of the top of my head, never replaced/regapped mine, do a search

the problem doesnt sound mechanical as you said the car idles fine/normal & builds boost as per normal.

am thinking a boost leak but you've said you already checked all hoses. could be a stuck open bov.

you've dropped 0.3 bar all of a sudden and theres misfiring, spluttering so am thikning theres still 0.9bar worth of fuel going in

Edited by Mike__
Dont know the gaps of the top of my head, never replaced/regapped mine, do a search

the problem doesnt sound mechanical as you said the car idles fine/normal & builds boost as per normal.

am thinking a boost leak but you've said you already checked all hoses. could be a stuck open bov.

you've dropped 0.3 bar all of a sudden and theres misfiring, spluttering so am thikning theres still 0.9bar worth of fuel going in

Just for a update the car is struggling to idle now, blowing black smoke on idle. Car still revs fine but with alot of miss fire.

Compression test will tell whats wrong.

hey white boy, your not the bloke with the blue gtr that i raced a few months back in my white one??

Yer man... had a few goodies since then. Now she is stuffed, hardly idles and blows white and blue smoke now...

Yer man... had a few goodies since then. Now she is stuffed, hardly idles and blows white and blue smoke now...

definently comp test it.

white smoke is unburnt fuel and blue is oil smoke.

almost sounds like a hole in a piston..

Just to correct that,

White smoke is coolant

Black is Petrol

Blue is oil

what ever mate.

EXCESS fuel is black smoke.

UNBURNT fuel from not unuf compression or no spark is white smoke.

water smoke is steam not smoke.

what ever mate.

EXCESS fuel is black smoke.

UNBURNT fuel from not unuf compression or no spark is white smoke.

water smoke is steam not smoke.

So now compression test is next....

If it is a piston that is stuffed is it possible to do a RB30 NA swap over? Any good guids out? I have found the PDF but it skipped alot of things like ECU ect....

[if it is a piston that is stuffed is it possible to do a RB30 NA swap over? Any good guids out? I have found the PDF but it skipped alot of things like ECU ect....

im thinking of doing an rb30 conversion as well, we'll have to have another drag after, lol

[if it is a piston that is stuffed is it possible to do a RB30 NA swap over? Any good guids out? I have found the PDF but it skipped alot of things like ECU ect....

im thinking of doing an rb30 conversion as well, we'll have to have another drag after, lol

compression test done

  • 1st 140
  • 2nd 140
  • 3rd 150
  • 4th 150
  • 5th 130
  • 6th 130

All rough figures being noob at it doesn't help. Give or take 5PSI. So what does this mean? Everything ok? I'm leaning towards the turbos now. Is there any way to check?

Do a diagnostic search, could easily be an AFM or cas or igniter.

Ok how do i check the AFM? I have unpluged them and notice both times the car nearly stalling but car ran the same. Do i need to clean them? If so what with? I have the stock air box and just a panel filter.

CAS? Crank angle sensor? is that on the front of the engine? Unpluged that and the car didn't start. Pluged it back in and the car was the same.

Fuel. Don't know how i'm spose to check the fuel pressure. I will ask my mech mate tomorrow.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...