Jump to content
SAU Community

Recommended Posts

  • Replies 42
  • Created
  • Last Reply

Top Posters In This Topic

i have a t67 i believe with a 8cm exhaust housing and have not been able to find a larger one to suit, you people with td06's do you know the exhast wheel size to compare, mine it 60mm from memory. Im not sure what to do atm as it will spool up nice and early with very little lag but not sure how much it will kill the top end.

Im not sure if the T67 uses the TD06H or the TD06 turbine, or another again. I have often read/seen ppl refer to the TD06-25G as the same turbo as the T67-25G, but there could easily be subtle differences, hence the different designation

What size are you after Clint as i have a 10cm and come the end of the week will know whether i want to go smaller, so may be able to trial fit one anothers and see how they go. I may even like to try the 8cm to see if i make the same top end power but with better response...perhaps telling me that my head, valves (???? i duuno) are more of a restriction then the exhaust housing on an RB20.

i would like a 12cm but a 10 would be ok too, thats why i need to find out if the TD06 has the same exh wheel, the blokes at MTQ said it was bigger than a TD06 and they couldnt find anything suitable in the misubishi range.

My engine is being done on a engine dyno so i dont wont to change it once fitted, so if i cant find something suitable i will just use it, can always add some extra power with Nos for the strip.

i think the 8cm is just another way of saying ar.. type thing.. just find out what a 8cm, 10cm, 12cm is equal to and there is your answer.. 8cm mite be .6 or something??? have a look at the ihi rx6 turbo.. very small exhaust housing but huge comp cover.. spools up at like 2800-3200 on sr20 but still packs enough for 300rwkw+ mite the same deal with your t67 with 8cm housing..

Dotn Apexi use a different convention again?

They typically have a P in front of their housing size referecne, which i think is the A/R in mm^2/mm, where as Garret use in^2/in so a Garret 0.87 equates to about the Apexi P22.

So how that helps me work out the Trust 8, 10, 12, 16 cm^2 housings i dont know ...anybody?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • What copper washer do you guys use on the bleeder bolts? The existing one I have I had no idea where to find it in a local store, I did buy some online but that are only 1mm thick whereas my old one is 2mm+ thick and when I put the new washer out and squeeze the top radiator hose I can hear a bit of air but not with the old one. Does this matter? The new one doesn't leak, but the inner diameter is a bit loose whereas the old one threads on the bolt.
    • Howdy all, after being out a few weeks ago on a spirited drive in my GTR I have 2 issues that oddly have appeared at the same time. Whilst accelerating quickly through the gears all of a sudden i’ve lost power at the top of third gear (below redline around 6000rpm) for no obvious reason.    From that point onwards the car has been running rich on idle, won’t really rev under load without a ton of black smoke and the odd backfire, and dying as a pull up to a set of lights unless I keep the revs up around 1500rpm. In addition when shutting down the car that same night (I was 10 minutes from home) I noticed one of the turbos was significantly noisy on wind down when shutting off the engine. After letting the car cool down overnight it starts up fine, although once it gets to temp the revs start to creep up and down, the exhaust is darker than it should be and it also sounds like it’s running rich (fat note) I’ve put a new set of plugs in it - no change, the old plugs all seemed OK with two of them being somewhat richer/fueled up than the other 3 with 1 being borderline. I’ve smoked tested the intake system via the front of the Turbos, found a split vacuum hose going to the factory boost gauge sender, which I have since replaced.  Also found another leak on the gasket coming off the rear turbo outlet, have also replaced this. After fixing both of these leaks - still have the running rich issue. I’ve also tried another pair of AFM’s - no change here After pulling off the front turbo intake pipes, there is obvious shaft play in the front turbo, which now hisses loudly on light revvs although I can’t see why this would make the car run funny even under idle. I’m curious to know why it’s running rich before I potentially replace/rebuild turbos. The car is completely stock <50,000kms  other than an exhaust. Oil and coolant are all clear. I haven’t bothered with coil packs as it looks like they won’t be the issue due to condition of the plugs. Any help appreciated as I cry myself to sleep!
    • No probs at all. I used to love trying to dig up obscure info for those in need where possible going back 20+ years on SAU.  I did have another look and couldn't come up with any closer match. I'm leaning towards those skirts in your first pic are custom fitments, cut down/extended or from another car entirely and modded to fit an R34 sedan. I would've thought someone in Japan had them and taken a photo at some stage over the last 2 decades but there's nothing. Someone out there must know surely.
    • Welcome mate. Any pics? Even with a DE I'd be well happy if I had that as a 1st car. 
×
×
  • Create New...