Jump to content
SAU Community

Recommended Posts

  • Replies 42
  • Created
  • Last Reply

Top Posters In This Topic

i have a t67 i believe with a 8cm exhaust housing and have not been able to find a larger one to suit, you people with td06's do you know the exhast wheel size to compare, mine it 60mm from memory. Im not sure what to do atm as it will spool up nice and early with very little lag but not sure how much it will kill the top end.

Im not sure if the T67 uses the TD06H or the TD06 turbine, or another again. I have often read/seen ppl refer to the TD06-25G as the same turbo as the T67-25G, but there could easily be subtle differences, hence the different designation

What size are you after Clint as i have a 10cm and come the end of the week will know whether i want to go smaller, so may be able to trial fit one anothers and see how they go. I may even like to try the 8cm to see if i make the same top end power but with better response...perhaps telling me that my head, valves (???? i duuno) are more of a restriction then the exhaust housing on an RB20.

i would like a 12cm but a 10 would be ok too, thats why i need to find out if the TD06 has the same exh wheel, the blokes at MTQ said it was bigger than a TD06 and they couldnt find anything suitable in the misubishi range.

My engine is being done on a engine dyno so i dont wont to change it once fitted, so if i cant find something suitable i will just use it, can always add some extra power with Nos for the strip.

i think the 8cm is just another way of saying ar.. type thing.. just find out what a 8cm, 10cm, 12cm is equal to and there is your answer.. 8cm mite be .6 or something??? have a look at the ihi rx6 turbo.. very small exhaust housing but huge comp cover.. spools up at like 2800-3200 on sr20 but still packs enough for 300rwkw+ mite the same deal with your t67 with 8cm housing..

Dotn Apexi use a different convention again?

They typically have a P in front of their housing size referecne, which i think is the A/R in mm^2/mm, where as Garret use in^2/in so a Garret 0.87 equates to about the Apexi P22.

So how that helps me work out the Trust 8, 10, 12, 16 cm^2 housings i dont know ...anybody?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...