Jump to content
SAU Community

Recommended Posts

Fuel cooler is mounted at front of car . In front of radiator, behind grill. A/c condenser has been removed oil cooler is also mounted in its location. I didnt like the oil cooler mounting in front of front wheel..I'll try track down some pics

Fuel cooler is mounted at front of car . In front of radiator, behind grill. A/c condenser has been removed oil cooler is also mounted in its location. I didnt like the oil cooler mounting in front of front wheel..I'll try track down some pics

Yea I've got my oil cooler in front of my front wheel, I don't think it's very effiencent there

My 83/75 results is a page or 2 back

The fmw has a different wheel design yea

My 32 gtr was rebuilt with the following parts and was run in and tuned by Sean at EFI Performance

Engine:

Rb26 (2.6l)

Cosworth forged pistons (87mm)

Manley conrods

R34 gtr crankshaft ( new from Nissan)

Acl race bearings

Arp rod, head, main bolts

Reimax billet oil pump gear

Tomei 1.5 mm head gasket

Kelford 282 cams

Manley valve springs with ti retainers

Sump baffles

Oil cooler

Balanced and blueprinted

Os giken twin plate button clutch rebuilt by NPC

Machine work done by chilton engineering

Engine assembled by Dan at ERD

Greddy plennum

Greddy 100mm pipe kit

100mm intercooler

Turbonetics billet gtk 1050 turbo with .86 twin scroll rear housing

Turbosmart 60mm wastegate

2.5 inch screamer pipe

6 boost exh manifold hpc coated with egt ports

4 inch dumpipe

3 inch decat pipe

3 inch TItanium cat back exhaust

Magnafuel 750 pro tuner fuel pump ( 2000hp)

Bosch 044 (lift pump)

7 litre surge tank

Fuel cooler

Aeromotive fpr

Bosch 2200 cc injectors

All braided hoses

Splitfire coil packs

Power fc dejetro

Car made 650hp at 26 psi (485kw)

I will post a pic of Dyno chart soon.

The ignition system is at limit at 26 psi

I have just finished installing ls2 truck coils and an ati balancer. Next tune the boost is being increased and rev limit is being increased.

Aiming for 700hp + on 30 psi.

Will post results when it is sorted.

Thanks, no port work on head just reconditioned with valve springs, retainers, shims etc.

Running on Caltex eflex atm. This setup needs to be run on drum E85 to get more out of it. The motor/turbo can quite easily handle 40psi. Not too confident on the consistency of pump ethanol. However, this is still a street car and 650hp should be enough for the std gearbox atm...lol.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...